background image

Notes, Cautions, and Warnings

 

NOTE: 

A NOTE indicates important information that helps you make better 

use of your product.

 

CAUTION: 

A CAUTION indicates either potential damage to hardware or 

loss of data, and tells you how to avoid the problem.

 

WARNING:  

A WARNING indicates a potential for property damage, 

personal injury, or death.

____________________

Information in this document is subject to change without notice.
© 2011 Dell Inc. All rights reserved.

Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc. 
is strictly forbidden.

Trademarks used in this text: Dell™ and the DELL logo are trademarks of Dell Inc. Alienware

®

 is a 

registered trademark of Alienware Corporation. Microsoft

®

, Windows

®

, and the Windows start button 

logo are either trademarks or registered trademarks of Microsoft Corporation in the United States and/
or other countries.

Other trademarks and trade names may be used in this document to refer to either the entities claiming 
the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and 
trade names other than its own.

2011 - 12

Rev. A00

book.book  Page 2  Wednesday, May 16, 2012  2:37 PM

Summary of Contents for Alienware Aurora R4



































































































































































Reviews: