Dell Command Line Interface User Manual Download | Manualshive

Page: 98 / 226

background image

98

omconfig: Managing Components Using the Instrumentation Service

Example Shutdown Commands

To set the shutdown action to reboot, type:

omconfig system shutdown action=reboot

To bypass operating system shutdown before the system is powered off, type:

omconfig system shutdown action=reboot osfirst=false

omconfig system thrmshutdown

Use the

omconfig system thrmshutdown

command to configure a thermal shutdown action. A thermal

shutdown can be configured to occur when a temperature probe detects a temperature probe warning or
failure event.

Table 4-30 shows the valid parameters for the command.

Table 4-29.

Shutdown Parameters

name=value pair

Description

action=reboot

Shuts down the operating system and initiates system startup, performing BIOS checks
and reloading the operating system.

action=poweroff

Turns the electrical power to the system off.

action=powercycle

Turns the electrical power to the system off, pauses, turns the power on, and reboots the
system. Power cycling is useful when you want to reinitialize system components such as
hard drives.

osfirst=true | false

true

: Closes the file system and exits the operating system before shutting down the

system.

false

: Does not close the file system or shut down the operating system before shutting

down the system.

Table 4-30.

Thermal Shutdown Parameters

name=value pair

Description

severity=disabled | warning | failure

disabled

: Disable thermal shutdown. An administrator must intervene.

warning

: Perform a shutdown when a temperature warning event is

detected. A warning event occurs when any temperature probe inside a
chassis reads a temperature (in degrees Celsius) which exceeds the
maximum temperature warning threshold.

failure

: Perform a shutdown when a temperature failure event is

detected.

A failure event occurs when any temperature probe inside a chassis reads
a temperature (in degrees Celsius) that exceeds the maximum
temperature failure threshold.

«
...
96
97
98
99
100
...
»

Summary of Contents for Command Line Interface



































































































































































































































Reviews:

No comments

Related manuals for Command Line Interface

Brand: Ubiquiti Pages: 50

BroadLink SP3353

Brand: MicroNet Pages: 66

NJ220 - IntelliJack Switch

Brand: 3Com Pages: 82

Conel UR5i v2 Libratum

Brand: B&B Electronics Pages: 32

Brand: Tbus Pages: 25

Brand: Faderfox Pages: 10

Brand: NC-link Pages: 20

Brand: Quantum Pages: 7

Brand: IBM Pages: 72

Brand: Black Box Pages: 12

Routers and Switches

Brand: Allied Telesis Pages: 15

DTS 4020.timebridge

Brand: Mobatime Pages: 94

Odin CL-4 Connect

Brand: DAPAudio Pages: 20

Brand: ICP DAS USA Pages: 8

Brand: IBM Pages: 70

Brand: 3Egreen Pages: 10

Facility Explorer

Brand: Johnson Controls Pages: 33

Brand: Huawei Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands