Dell EU2SPE Disassembly Instructions Manual Download

Page: 3 / 16

Table 1 Acronym List (continued)

Acrony
m

Meaning

LCC

Link Control Card

LDPE

Low-Density Polyethylene

Lead

PBB

Polybrominated Biphenyls

PBDE

Polybrominated Diphenyl Ethers

Polycarbonate

PCB

Printed Circuit Board

PCT

Polychlorinated Terphenyl

Palladium

PETE or
PET

Polyethylene Terephthalate

Polypropylene

Polystyrene

Platinum

PVC

Polyvinyl Chloride

RoHS

Restriction of Hazardous Substances

SAS

Serial Attached SCSI

Storage Processor

SPE

Storage Processor Enclosure

SSD

Solid State Disk

Volt

WEEE

Waste Electrical and Electronic Equipment

Product identification

Note:The Product Regulatory Model Name is used as the main identifier throughout
this document. Locate the product regulatory model name on the Device Rating Label
(DRL) affixed to a rectangular recess on the top of the product chassis.

Table 2 Product Regulatory Model Name and Specifications

Product
Regulatory Model
Name

EU2SPE

Product
Description

2U, Disk Processor Enclosure (DPE) that supports 12, 3.5" disk drives; 1,
2.5" disk drive; and Input/Output modules.

WEEE Disassembly Instructions

Product identification

Summary of Contents for EU2SPE

















Search results

Summary of Contents for EU2SPE

Reviews:

Related manuals for EU2SPE

Brands by name

Popular brands

Dell EU2SPE, Disassembly Instructions Manual

Search results

Summary of Contents for EU2SPE

Reviews:

Related manuals for EU2SPE

Brands by name

Popular brands