active [
rate
]
(OPTIONAL) Enter the keyword
active
to view only active multicast
routes. Enter a rate to view active routes over the specified rate. The
range is 0 to 10000000.
count
(OPTIONAL) Enter the keyword
count
to view the number of
multicast routes and packets on the E-Series.
snooping [vlan
vlan-id
] [
group-
address
[
source-
address
]]
(OPTIONAL) E-Series ExaScale and S4810 only:
Enter the keyword
snooping
to display information on the multicast
routes discovered by PIM-SM snooping.
Enter a VLAN ID to limit the information displayed to the multicast
routes discovered by PIM-SM snooping on a specified VLAN. the
valid VLAN ID range is 1 to 4094.
Enter a multicast group address and, optionally, a source multicast
address in dotted decimal format (A.B.C.D) to limit the information
displayed to the multicast routes discovered by PIM-SM snooping for
a specified multicast group and source.
summary
(OPTIONAL) Enter the keyword
summary
to view routes in a tabular
format.
Command Modes
•
EXEC
•
EXEC Privilege
Command History
Version 8.4.1.1
Support for the keyword
snooping
and the optional
vlan vlan-
id
,
group-address
, and
source-address
parameters were
added on E-Series ExaScale.
Version 8.3.7.0
Introduced on the S4810.
Version 7.6.1.0
Introduced on the S-Series.
Version 7.5.1.0
Introduced on the C-Series.
E-Series legacy
command
Example (Static)
FTOS#show ip mroute static
Mroute: 23.23.23.0/24, interface: Lo 2
Protocol: static, distance: 0, route-map: none, last change:
00:00:23
Example
(Snooping)
FTOS#show ip mroute snooping
IPv4 Multicast Snooping Table
(*, 224.0.0.0), uptime 17:46:23
Incoming vlan: Vlan 2
Outgoing interface list:
GigabitEthernet 4/13
(*, 225.1.2.1), uptime 00:04:16
Incoming vlan: Vlan 2
1016
Summary of Contents for Force10 Z9000
