Usage
Information
The following describes the
show ip ospf
process-id
interface
command
shown in the Example below.
Item
Description
GigabitEthernet...
This line identifies the interface type slot/port and the status of the
OSPF protocol on that interface.
Internet Address...
This line displays the IP address, network mask and area assigned to
this interface.
Process ID...
This line displays the OSPF Process ID, Router ID, Network type and
cost metric for this interface.
Transmit Delay...
This line displays the interface’s settings for Transmit Delay, State,
and Priority. In the State setting, BDR is Backup Designated Router.
Designated Router...
This line displays the ID of the Designated Router and its interface
address.
Backup
Designated...
This line displays the ID of the Backup Designated Router and its
interface address.
Timer intervals...
This line displays the interface’s timer settings for Hello interval,
Dead interval, Transmit Delay (Wait), and Retransmit Interval.
Hello due...
This line displays the amount time untill the next Hello packet is sent
out this interface.
Neighbor Count...
This line displays the number of neighbors and adjacent neighbors.
Listed below this line are the details about each adjacent neighbor.
Example
FTOS>show ip ospf int
GigabitEthernet 13/17 is up, line protocol is up
Internet Address 192.168.1.2/30, Area 0.0.0.1
Process ID 1, Router ID 192.168.253.2, Network Type
BROADCAST, Cost: 1
Transmit Delay is 1 sec, State DR, Priority 1
Designated Router (ID) 192.168.253.2, Interface address
192.168.1.2
Backup Designated Router (ID) 192.168.253.1, Interface
address 192.168.1.1
Timer intervals configured, Hello 10, Dead 40, Wait 40,
Retransmit 5
Hello due in 00:00:02
Neighbor Count is 1, Adjacent neighbor count is 1
Adjacent with neighbor 192.168.253.1 (Backup Designated
Router)
GigabitEthernet 13/23 is up, line protocol is up
Internet Address 192.168.0.1/24, Area 0.0.0.1
Process ID 1, Router ID 192.168.253.2, Network Type
BROADCAST, Cost: 1
Transmit Delay is 1 sec, State DROTHER, Priority 1
Designated Router (ID) 192.168.253.5, Interface address
192.168.0.4
Backup Designated Router (ID) 192.168.253.3, Interface
address 192.168.0.2
Timer intervals configured, Hello 10, Dead 40, Wait 40,
Retransmit 5
1092
Summary of Contents for Force10 Z9000
