Example
FTOS#show ip ospf 34 neighbor
Neighbor ID Pri State Dead Time Address Interface Area
20.20.20.7 1 FULL/DR 00:00:32 182.10.10.3 Gi 0/0 0.0.0.2
192.10.10.2 1 FULL/DR 00:00:37 192.10.10.2 Gi 0/1 0.0.0.1
20.20.20.1 1 FULL/DROTHER00:00:36 192.10.10.4 Gi 0/1 0.0.0.1
FTOS#
show ip ospf routes
Display routes as calculated by OSPF and stored in OSPF RIB.
C-Series, E-Series, S-Series, Z-Series, S4810
Syntax
show ip ospf
process-id
routes
Parameters
process-id
Enter the OSPF Process ID to show a specific process. If no Process
ID is entered, command applies only to the first OSPF process.
Defaults
none
Command Modes
•
EXEC
•
EXEC Privilege
Command History
Version 8.3.11.1
Introduced on the Z9000.
Version 8.3.7.0
Introduced on the S4810.
Version 7.8.1.0
Added support for Multi-Process OSPF.
Version 7.6.1.0
Introduced on the S-Series.
Version 7.5.1.0
Introduced on the C-Series and E-Series.
Usage
Information
This command is useful in isolating routing problems between the OSPF and the RTM. For
example, if a route is missing from the RTM/FIB but is visible from the display output of this
command, the problem is with downloading the route to the RTM.
This command has the following limitations:
•
The display output is sorted by prefixes; intra-area ECMP routes are not displayed
together.
•
For Type 2 external routes, Type 1 cost is not displayed.
Example
FTOS#show ip ospf 100 route
Prefix Cost Nexthop Interface Area Type
1.1.1.1 1 0.0.0.0 Lo 0 0 Intra-Area
3.3.3.3 2 13.0.0.3 Gi 0/47 1 Intra-Area
13.0.0.0 1 0.0.0.0 Gi 0/47 0 Intra-Area
150.150.150.0 2 13.0.0.3 Gi 0/47 - External
172.30.1.0 2 13.0.0.3 Gi 0/47 1 Intra-Area
FTOS#
1094
Summary of Contents for Force10 Z9000
