35
PIM-Source Specific Mode (PIM-SSM)
The protocol-independent multicast (PIM)-source specific mode (PIM-SSM) commands are supported by the Dell
Force10 operating software (FTOS) on all E-Series, C-Series, S-Series, Z-Series, or S4810 platforms.
ip pim ssm-range
Specify the SSM group range using an access list.
C-Series, E-Series, S-Series, Z-Series, S4810
Syntax
ip pim ssm-range {
access_list_name
}
Parameters
access_list_nam
e
Enter the name of the access list.
Defaults
Default SSM range is 232/8 and ff3x/32
Command Modes
CONFIGURATION
Command History
Version 8.3.11.1
Introduced on the Z9000.
Version 8.3.7.0
Introduced on the S4810.
Version 8.1.1.0
Introduced on the E-Series ExaScale.
Version 7.8.1.0
Introduced on the S-Series.
Version 7.7.1.0
Introduced on the C-Series.
Version 7.5.1.0
Introduced on the E-Series.
Usage
Information
FTOS supports standard access lists for the SSM range. You cannot use extended ACLs for
configuring the SSM range. If you configure an extended ACL and then used in the
ip pim
ssm-range {
access list name
}
configuration, an error is reported.
However, if you configure
ip pim ssm-range {
access list name
}
first and then
you configure the ACL as an Extended ACL, an error is not reported and the ACL is not applied
to the SSM range.
FTOS-recommended best-practices are to configure the standard ACL, and then apply the ACL
to the SSM range. After the SSM range is applied, the changes are applied internally without
requiring clearing of the tree information base (TIB).
When the ACL rules change, the ACL and protocol-independent multicast (PIM) modules apply
the new rules automatically.
1147
Summary of Contents for Force10 Z9000
