Version 6.5.1.0
Expanded the command to permit configuration on port channels.
pre-Version
6.1.1.1
Introduced on the E-Series.
Usage
Information
Enter this command to honor all incoming 802.1p markings on incoming switched traffic on the
interface. By default, this facility is not enabled (that is, the 802.1p markings on incoming traffic
are not honored).
You can apply this command on both physical interfaces and port channels. When you set the
service-class dynamic for a port channel, the physical interfaces assigned to the port channel
are automatically configured; you cannot assign the
service-class dynamic
command
to individual interfaces in a port channel.
On the C-Series and S-Series, all traffic is by default mapped to the same queue, Queue 0. If
you honor dot1p on ingress, you can create service classes based the queueing strategy using
the
service-class dynamic dot1p
command from INTERFACE mode. You may apply
this queuing strategy to all interfaces by entering this command from CONFIGURATION mode.
•
All dot1p traffic is mapped to Queue 0 unless you enble the
service-class
dynamic dot1p
command on an interface or globally.
•
Layer 2 or Layer 3 service policies supercede dot1p service classes.
show interfaces rate
Display information of either rate limiting or rate policing on the interface.
E-Series
Syntax
show interfaces [
interface
] rate [limit | police]
Parameters
interface
(OPTIONAL) Enter the following keywords and slot/port or number
information:
•
For a 100/1000 Ethernet interface, enter the keyword
GigabitEthernet
followed by the slot/port information.
•
For a 1-Gigabit Ethernet interface, enter the keyword
GigabitEthernet
followed by the slot/port information.
•
For a SONET interface, enter the keyword
sonet
followed by
the slot/port information.
•
For a 10-Gigabit Ethernet interface, enter the keyword
TenGigabitEthernet
followed by the slot/port
information.
limit
(OPTIONAL) Enter the keyword
limit
to view the outgoing traffic
rate.
police
(OPTIONAL) Enter the keyword
police
to view the incoming traffic
rate.
1188
Summary of Contents for Force10 Z9000
