peak
peak-rate
(OPTIONAL) Enter the keyword
peak
followed by a number to specify
the peak rate in Mbps. The range is 0 to 10000. The default is the
same as designated for
committed-rate
.
Defaults
Burst size is 50 KB.
peak-rate
is by default the same as
committed-rate
. Granularity
for
committed-rate
and
peak-rate
is Mbps unless you use the
kbps
option.
Command Modes
QOS-POLICY-OUT
Command History
Version 8.2.1.0
Added the
kbps
option on the E-Series.
Version 7.7.1.0
Removed from the C-Series.
Version 7.5.1.0
Introduced on the C-Series.
pre-Version
6.1.1.1
Introduced on the E-Series.
Related
Commands
rate limit
– specifies the rate-limit functionality on the selected interface.
qos-policy-output
– creates a QoS output policy.
rate-police
Specify the policing functionality on incoming traffic.
C-Series, E-Series, S-Series, Z-Series, S4810
Syntax
rate-police [kbps]
committed-rate
[burst-KB] [peak [kbps]
peak-
rate
[
burst-KB
]]
Parameters
kbps
Enter the keyword
kbps
to specify the rate limit in Kilobits per
second (Kbps). On C-Series and S-Series, make the following value a
multiple of 64. On the E-Series, Force10 recommends using a value
greater than or equal to 512 as lower values does not yield accurate
results. The range is 0 to 10000000. The default granularity is
Megabits per second (Mbps).
committed-rate
Enter the bandwidth in Mbps. The range is 0 to 10000.
burst-KB
(OPTIONAL) Enter the burst size in KB. The range is 16 to 200000. The
default is 50.
peak
peak-rate
(OPTIONAL) Enter the keyword
peak
followed by a number to specify
the peak rate in Mbps. The range is 0 to 10000. The default is the
same as designated for
committed-rate
.
Defaults
Burst size is 50 KB.
peak-rate
is by default the same as
committed-rate
. Granularity
for
committed-rate
and
peak-rate
is Mbps unless you use the
kbps
option.
Command Modes
QOS-POLICY-IN
1209
Summary of Contents for Force10 Z9000
