Usage
Information
The VRRP group only becomes active and sends VRRP packets when a virtual IP address is
configured. When you delete the virtual address, the VRRP group stops sending VRRP packets.
A system message appears after you enter or delete the
virtual-address
command.
To guarantee that a VRRP group becomes MASTER, configure the VRRP group’s virtual
address with the same IP address as the interface’s primary IP address and change the priority
of the VRRP group to 255.
You can ping the virtual addresses configured in all VRRP groups.
vrrp delay minimum
Set the delay time for VRRP initialization after an interface comes up.
Z-Series, S4810
Syntax
vrrp delay minimum
seconds
Parameters
seconds
Enter the number of seconds for the delay for VRRP initialization after
an interface becomes operational. The range is 0 to 900 (0 indicates
no delay).
Defaults
0
Command Modes
INTERFACE
Command History
Version 9.0.0.0
Introduced on the Z9000.
Version 8.3.8.0
Introduced on the S4810.
Usage
Information
This command applies to a single interface. When used in conjunction with the
vrrp delay
reload
CLI, the later timer rules the VRRP enabling. For example, if
vrrp delay reload
is 600 and the
vrrp delay minimum
is 300:
•
When the system reloads, VRRP waits 600 seconds (10 minutes) to bring up VRRP on all
interfaces that are up and configured for VRRP.
•
When an interface comes up, whether as part of a system reload or an interface
reload, the system waits 300 seconds (5 minutes) to bring up VRRP on that interface.
Related
Command
vrrp delay reload
– sets the delay time for VRRP initialization after a system reboot.
vrrp delay reload
Set the delay time for VRRP initialization after a system reboot.
Z-Series, S4810
Syntax
vrrp delay reload
seconds
Parameters
seconds
Enter the number of seconds for the delay. The range is 0 to 900 (0
indicates no delay).
1482
Summary of Contents for Force10 Z9000
