Parameters
source
Enter the IP address of the network or host from which the packets
were sent.
mask
Enter a network mask in /prefix format (/x) or A.B.C.D. The mask,
when specified in A.B.C.D format, may be either contiguous or non-
contiguous.
any
Enter the keyword
any
to specify that all routes are subject to the
filter.
host
ip-address
Enter the keyword
host
and then enter the IP address to specify a
host IP address.
dscp
Enter the keyword
dscp
to deny a packet based on the DSCP value.
The range is 0 to 63.
operator
(OPTIONAL) Enter one of the following logical operand:
•
eq
= equal to
•
neq
= not equal to
•
gt
= greater than
•
lt
= less than
•
range
= inclusive range of ports (you must specify two ports
for the
port
parameter)
port port
Enter the application layer port number. Enter two port numbers if you
are using the
range
logical operand. The range is 0 to 65535.
destination
Enter the IP address of the network or host to which the packets are
sent.
count
(OPTIONAL) Enter the keyword
count
to count packets processed
by the filter.
byte
(OPTIONAL) Enter the keyword
byte
to count bytes processed by
the filter.
log
(OPTIONAL, E-Series only) Enter the keyword
log
to have the
information kept in an ACL log file.
order
(OPTIONAL) Enter the keyword
order
to specify the QoS priority for
the ACL entry. The range is 0 to 254 (where 0 is the highest priority
and 254 is the lowest; lower order numbers have a higher priority). If
you do not use the keyword
order
, the ACLs have the lowest order
by default (255).
monitor
(OPTIONAL) Enter the keyword
monitor
when the rule is describing
the traffic that you want to monitor and the ACL in which you are
creating the rule is applied to the monitored interface.
NOTE: For more information, refer to the Flow-based Monitoring
section in the Port Monitoring chapter of the
FTOS Configuration
Guide
.
fragments
Enter the keyword
fragments
to use ACLs to control packet
fragments.
252
Summary of Contents for Force10 Z9000
