seq
Assign a sequence number to a deny or permit filter in a MAC access list while creating the filter.
C-Series, E-Series, S-Series, Z-Series
Syntax
seq
sequence-number
{deny | permit} {any |
mac-source-address
[
mac-source-address-mask
]} [count [byte]] [log] [monitor]
To remove this filter, use the
no seq
sequence-number
command.
Parameters
sequence-
number
Enter a number between 0 to 65535.
deny
Enter the keyword
deny
to configure a filter to drop packets meeting
this condition.
permit
Enter the keyword
permit
to configure a filter to forward packets
meeting this criteria.
any
Enter the keyword
any
to filter all packets.
mac-source-
address
Enter a MAC address in nn:nn:nn:nn:nn:nn format.
mac-source-
address-mask
(OPTIONAL) Specify which bits in the MAC address must match. If no
mask is specified, a mask of 00:00:00:00:00:00 is applied (in other
words, the filter allows only MAC addresses that match).
count
(OPTIONAL) Enter the keyword
count
to count packets the filter
processes.
byte
(OPTIONAL) Enter the keyword
byte
to count bytes the filter
processes.
log
(OPTIONAL, E-Series only) Enter the keyword
log
to log the packets.
monitor
(OPTIONAL) Enter the keyword
monitor
when the rule is describing
the traffic that you want to monitor and the ACL in which you are
creating the rule is applied to the monitored interface.
NOTE: For more information, refer to the “Flow-based Monitoring”
section in the Port Monitoring chapter of the
FTOS Configuration
Guide
.
Defaults
Not configured
Command Modes
CONFIGURATION-MAC ACCESS LIST-STANDARD
Command History
Version 8.3.11.1
Introduced on the Z9000.
Version 8.1.1.0
Introduced on the E-Series ExaScale.
Version 7.6.1.0
Introduced on the S-Series.
Version 7.5.1.0
Introduced on the C-Series.
269
Summary of Contents for Force10 Z9000
