Version 8.3.7.0
Introduced on the S4810.
Version 7.8.1.0
Introduced on the S-Series.
Version 7.7.1.0
Introduced on the C-Series.
Usage
Information
When a BGP cluster contains only one route reflector, the cluster ID is the route reflector’s
router ID. For redundancy, a BGP cluster may contain two or more route reflectors. Assign a
cluster ID with the
bgp cluster-id
command. Without a cluster ID, the route reflector
cannot recognize route updates from the other route reflectors within the cluster.
The default format for displaying the cluster-id is dotted decimal, but if you enter the cluster-id
as an integer, it is displayed as an integer.
Related
Commands
bgp client-to-client reflection
– enables route reflection between the route reflector and
clients.
neighbor route-reflector-client
– configures a route reflector and clients.
show ip bgp cluster-list
– views paths with a cluster ID.
bgp confederation identifier
Configure an identifier for a BGP confederation.
C-Series, E-Series, S-Series, Z-Series, S4810
Syntax
bgp confederation identifier
as-number
To delete a BGP confederation identifier, use the
no bgp confederation
identifier as-number
command.
Parameters
as-number
Enter the AS number. The range is 0 to 65535 (2-byte), 1 to 4294967295
(4-byte), or 0.1 to 65535.65535 (dotted format).
Defaults
Not configured.
Command Modes
ROUTER BGP
Command History
Version 8.3.11.1
Introduced on the Z9000.
Version 8.3.7.0
Introduced on the S4810.
Version 7.8.1.0
Introduced on the S-Series.
Version 7.7.1.0
Introduced on the C-Series. Added support for the 4-byte format
Usage
Information
You must configure your system to accept 4-byte formats before entering a 4-byte AS number.
All the routers in the Confederation must be 4– or 2-byte identified routers. You cannot mix
them.
The autonomous systems configured in this command are visible to the EBGP neighbors. Each
autonomous system is fully meshed and contains a few connections to other autonomous
systems. The next hop, MED, and local preference information is preserved throughout the
confederation.
337
Summary of Contents for Force10 Z9000
