Parameters
ip-address
Enter the IP address of the neighbor in dotted decimal format.
peer-group-name
Enter the name of the peer group.
maximum
Enter a number as the maximum number of prefixes allowed for this
BGP router. The range is 1 to 4294967295.
threshold
(OPTIONAL) Enter a number to be used as a percentage of the
maximum value. When the number of prefixes reaches this
percentage of the maximum value, the E-Series software sends a
message. The range is 1 to 100 percent. The default is 75.
warning-only
(OPTIONAL) Enter the keyword
warning-only
to set the router to
send a log message when the maximum value is reached. If this
parameter is not set, the router stops peering when the maximum
number of prefixes is reached.
Defaults
threshold = 75
Command Modes
ROUTER BGP
Command History
Version 8.3.11.1
Introduced on the Z9000.
Version 8.3.7.0
Introduced on the S4810.
Version 7.8.1.0
Introduced on the S-Series.
Version 7.7.1.0
Introduced on the C-Series.
Usage
Information
If you configure the
neighbor maximum-prefix
command and the neighbor receives
more prefixes than allowed by the
neighbor maximum-prefix
command configuration,
the neighbor goes down and the
show ip bgp summary
command displays (prfxd) in the
State/PfxRcd column for that neighbor. The neighbor remains down until you enter the
clear
ip bgp
command for the neighbor or the peer group to which the neighbor belongs or you
enter the
neighbor shutdown
and
neighbor no shutdown
commands.
Related
Commands
show ip bgp summary
– displays the current BGP configuration.
neighbor next-hop-self (C-, E-, and S-Series)
Allows you to configure the router as the next hop for a BGP neighbor. (This command is used for IBGP).
C-Series, E-Series, S-Series, Z-Series
Syntax
neighbor {
ip-address
|
peer-group-name
} next-hop-self
To return to the default setting, use the
no neighbor {
ip-address
|
peer-group-
name
} next-hop-self
command.
Parameters
ipv6-address
Enter the IP address of the neighbor in dotted decimal format.
peer-group-name
(OPTIONAL) Enter the name of the peer group.
Defaults
Disabled.
368
Summary of Contents for Force10 Z9000
