To disable route dampening, use the
no bgp dampening [
half-life reuse
suppress max-suppress-time
] [route-map
map-name
]
command.
Parameters
half-life
(OPTIONAL) Enter the number of minutes after which the Penalty is
decreased. After the router assigns a Penalty of 1024 to a route, the
Penalty is decreased by half after the half-life period expires. The
range is 1 to 45. The default is 15 minutes.
reuse
(OPTIONAL) Enter a number as the reuse value, which is compared to
the flapping route’s Penalty value. If the Penalty value is less than the
reuse value, the flapping route is once again advertised (or no longer
suppressed). The range is 1 to 20000. The default is 750.
suppress
(OPTIONAL) Enter a number as the suppress value, which is
compared to the flapping route’s Penalty value. If the Penalty value is
greater than the suppress value, the flapping route is no longer
advertised (that is, it is suppressed). The range is 1 to 20000. The
default is 2000.
max-suppress-
time
(OPTIONAL) Enter the maximum number of minutes a route can be
suppressed. The default is four times the half-life value. The range is
1 to 255. The default is 60 minutes.
route-map
map-
name
(OPTIONAL) Enter the keywords
route-map
followed by the name
of a configured route map. Only match commands in the configured
route map are supported.
Defaults
Disabled.
Command Modes
ROUTER BGPV6-ADDRESS FAMILY
Command History
Version 8.2.1.0
Introduced on the E-Series ExaScale.
Version 7.4.1.0
Introduced
Usage
Information
If you enter
bgp dampening
, the default values for
half-life
,
reuse
,
suppress
, and
max-suppress-time
are applied. The parameters are position-dependent; therefore, if
you configure one parameter, you must configure the parameters in the order they appear in
the command.
Related
Commands
show ip bgp dampened-paths
– views the BGP paths.
bgp default local-preference
Change the default local preference value for routes exchanged between internal BGP peers.
C-Series, E-Series
Syntax
bgp default local-preference
value
To return to the default value, use the
no bgp default local-preference
command.
460
Summary of Contents for Force10 Z9000
