Line
Description
Rate information...
Estimate of the input and output traffic rate over a designated
interval (30 to 299 seconds). Traffic rate is displayed in bits, packets
per second, and percent of line rate.
Time since...
Elapsed time since the last interface status change (hh:mm:ss
format).
Example
FTOS#show interfaces
TenGigabitEthernet 2/0 is down, line protocol is down
Hardware is DellForce10Eth, address is 00:01:e8:8b:3d:e7
Current address is 00:01:e8:8b:3d:e7
Pluggable media present, Media type is unknown
Wavelength unknown
Interface index is 100992002
Internet address is not set
MTU 1554 bytes, IP MTU 1500 bytes
LineSpeed auto
Flowcontrol rx on tx off
ARP type: ARPA, ARP Timeout 04:00:00
Last clearing of "show interface" counters 3d17h53m
Queueing strategy: fifo
Input Statistics:
0 packets, 0 bytes
0 64-byte pkts, 0 over 64-byte pkts, 0 over 127-byte pkts
0 over 255-byte pkts, 0 over 511-byte pkts, 0 over 1023-byte
pkts
0 Multicasts, 0 Broadcasts
0 runts, 0 giants, 0 throttles
0 CRC, 0 overrun, 0 discarded
Output Statistics:
0 packets, 0 bytes, 0 underruns
0 64-byte pkts, 0 over 64-byte pkts, 0 over 127-byte pkts
0 over 255-byte pkts, 0 over 511-byte pkts, 0 over 1023-byte
pkts
0 Multicasts, 0 Broadcasts, 0 Unicasts
0 throttles, 0 discarded, 0 collisions, 0 wreddrops
Rate info (interval 299 seconds):
Input 00.00 Mbits/sec, 0 packets/sec, 0.00% of line-rate
Output 00.00 Mbits/sec, 0 packets/sec, 0.00% of line-rate
Time since last interface status change: 3d17h51m
Usage
Information
On the C-Series and S-Series, the interface counter “over 1023-byte pkts” does not increment
for packets in the range 9216 > x < 1023.
The Management port is enabled by default (
no shutdown
). If necessary, use the
ip
address
command to assign an IP address to the Management port. If two RPMs are
installed in your system, use the
show redundancy
command to display which RPM is the
Primary RPM.
On the S4810 and Z9000, you can configure two global IPv6 addresses. To view the addresses,
use the
show
interface
managementethernet
command. If you try to configure a
third IPv6 address, a message displays. If auto-configuration is enabled, all IPv6 addresses on
that management interface are auto-configured. The first IPv6 address that is configured on
the management interface will be the primary address. If deleted, it must be re-added; the
secondary address is not promoted.
Example
(TeraScale)
FTOS#show interfaces tengigabitethernet 0/0
TenGigabitEthernet 3/0 is up, line protocol is up
724
Summary of Contents for Force10 Z9000
