interface configured and enabled in the Port Channel. If that first interface goes down, the Port
Channel does not change its designated speed; you must disable and re-enable the Port
Channel or change the order of the channel members configuration to change the designated
speed. If the Port Channel contains a mix of interfaces with 100 Mb/s speed and 1000 Mb/s
speed, the software disables those interfaces whose speed does not match the speed of the
first interface configured and enabled in the Port Channel. If that first interface goes down, the
Port Channel does not change its designated speed; you must disable and re-enable the Port
Channel or change the order of the channel members configuration to change the designated
speed. For more information about Port Channels, refer to the
FTOS Configuration Guide
.
Related
Commands
description
– assigns a descriptive text string to the interface.
interface port-channel
– creates a Port Channel interface.
shutdown
– disables/enables the port channel.
group
Group two LAGs in a supergroup (“fate-sharing group” or “failover group”).
C-Series, E-Series, S-Series, Z-Series, S4810
Syntax
group
group_number
port-channel
number
port-channel
number
To remove an existing LAG supergroup, use the
no group group_number
command.
Parameters
group_number
Enter an integer from 1 to 32 that uniquely identifies this LAG fate-
sharing group.
port-channel
number
Enter the keywords
port-channel
followed by an existing LAG
number. Enter this keyword/variable combination twice, identifying
the two LAGs to be paired.
Defaults
none
Command Modes
PORT-CHANNEL FAILOVER-GROUP (conf-po-failover-grp)
Command History
Version 8.3.11.1
Introduced on the Z9000.
Version 8.3.7.0
Introduced on the S4810.
Version 8.1.1.0
Introduced on the E-Series ExaScale.
Version 7.6.1.0
Introduced on the C-Series, E-Series, and S-Series.
Related
Commands
port-channel failover-group
– accesses PORT-CHANNEL FAILOVER-GROUP mode to configure
a LAG failover group.
show interfaces port-channel
– displays information on configured Port Channel groups.
754
Summary of Contents for Force10 Z9000
