IP: s=10.1.2.62 (local), d=10.1.2.3 (Ma 0/0), len 1500,
sending fragment
IP Fragment, Ident = 4741, fragment offset = 1480
IP: s=40.40.40.40 (local), d=224.0.0.5 (Gi 4/11), len 64,
sending broad/multicast
proto=89
IP: s=40.40.40.40 (local), d=224.0.0.6 (Gi 4/11), len 28,
sending broad/multicast
proto=2
IP: s=0.0.0.0, d=30.30.30.30, len 100, unroutable
ICMP type=8, code=0
IP: s=0.0.0.0, d=30.30.30.30, len 100, unroutable
ICMP type=8, code=0
Usage
Information
Use the
count
option to stop packets from flooding the user terminal when debugging is
turned on.
The
access-group
option supports only the equal to (
eq
) operator in TCP ACL rules. Port
operators not equal to (
neq
), greater than (
gt
), less than (
lt
), or
range
are not supported in
access-group option (refer to the Example below). ARP packets (
arp
) and Ether-type
(
ether-type
) are also not supported in the
access-group
option. The entire rule is
skipped to compose the filter.
The
access-group
option pertains to:
•
IP Protocol Number: 0 to 255
•
Internet Control Message Protocol (
icmp
) but not the ICMP message type (0-255)
•
Any Internet Protocol (
ip
)
•
Transmission Control Protocol (
tcp
) but not on the
rst
,
syn
, or
urg
bits
•
User Datagram Protocol (
udp
)
In the case of ambiguous access control list rules, the
debug ip packet access-
control
command is disabled. A message appears identifying the error (refer to the Example
below).
Example (Error
Messages)
FTOS#debug ip packet access-group test
%Error: port operator GT not supported in access-list debug
%Error: port operator LT not supported in access-list debug
%Error: port operator RANGE not supported in access-list debug
%Error: port operator NEQ not supported in access-list debug
FTOS#00:10:45: %RPM0-P:CP
%IPMGR-3-DEBUG_IP_PACKET_ACL_AMBIGUOUS_EXP: Ambiguous rules not
supported in access-list debug, access-list debugging is
turned off
FTOS#
783
Summary of Contents for Force10 Z9000
