show ip cam stack-unit
Display CAM entries for an S-Series or Z-Series switch.
S-Series, Z-Series
Syntax
show ip cam stack-unit
id
port-set
pipe-number
[
ip-address mask
[longer-prefixes] | summary]
Parameters
id
Enter the stack-unit ID.
The unit ID range is 0 to 7 for S-Series.
pipe-number
Enter the number of the Port-Pipe number. The S50n and S50V range
is 0 to 1. The S25N, S25P, and S25V range is 0 to 0.
ip-address mask
[longer-prefix]
(OPTIONAL) Enter the IP address and mask of a route to CAM entries
for that route only. Enter the keywords
longer-prefixes
to view
routes with a common prefix.
summary
(OPTIONAL) Enter the keyword
summary
to view a table listing route
prefixes and the total number routes which can be entered in to CAM.
Command Modes
•
EXEC
•
EXEC Privilege
Command History
Version 8.3.11.1
Introduced on the Z9000.
Version 7.7.1.0
Added support for up to seven stack members.
Version 7.6.1.0
Introduced on the S-Series.
Usage
Information
The following describes the
show ip cam
command shown in the Example below.
Field
Description
Destination
Displays the destination route of the index.
EC
Displays the number of equal cost multipaths (ECMP) available for
the default route for non-Jumbo line cards. For Jumbo line cards,
displays 0,1 when ECMP is more than eight.
CG
Displays 0.
V
Displays a 1 if the entry is valid and a 0 otherwise.
C
Displays the CPU bit. 1 indicates that a packet hitting this entry is
forwarded to the CP or RP2, depending on Egress port.
V Id
Displays the VLAN ID. If the entry is 0, the entry is not part of a VLAN.
Mac Addr
Displays the next-hop router’s MAC address.
811
Summary of Contents for Force10 Z9000
