valid-lifetime
|
infinite
Enter the amount of time that the prefix is advertised, or enter
infinite
for an unlimited amount of time. The range is 0 to
4294967295. The default is 2592000. The maximum value means that
the preferred lifetime does not expire for the valid-life time parameter.
preferred-lifetime
| infinite
Enter the amount of time that the prefix is preferred, or enter
infinite
for an unlimited amount of time. The range is 0 to
4294967295. The default is 604800. The maximum value means that the
preferred lifetime and does not expire.
Command Modes
INTERFACE
Command History
Version 8.3.11.1
Introduced on the Z9000.
Version 8.3.7.0
Introduced on the S4810.
Version 8.3.2.0
Introduced on the E-Series TeraScale, C-Series, and S-Series.
Usage
Information
By default, all prefixes configured as addresses on the interface are advertised. This command
allows control over the individual parameters per prefix; you can use the
default
keyword to
use the default parameters for all prefixes. If a prefix has been configured with lifetime
parameter values, the default values cannot be applied using the
ipv6 nd prefix
default no-autoconfig
command.
ipv6 route
Establish a static IPv6 route.
C-Series, E-Series, S-Series, Z-Series, S4810
Syntax
ipv6 route
ipv6-address prefix-length
{
ipv6-address
|
interface
|
interface ipv6-address
} [
distance
] [tag
value
] [permanent]
To remove the IPv6 route, use the
no ipv6 route
ipv6-address prefix-length
{
ipv6-address
|
interface
|
interface ipv6-address
} [
distance
]
[tag
value
] [permanent]
command.
Parameters
ipv6-address
prefix-length
Enter the IPv6 address in the x:x:x:x::x format followed by the prefix
length in the /x format. The range is /0 to /128.
NOTE: The :: notation specifies successive hexadecimal fields of
zeros.
interface
(OPTIONAL) Enter the following keywords and slot/port or number
information:
•
For a 1-Gigabit Ethernet interface, enter the keyword
GigabitEthernet
followed by the slot/port information.
•
For a loopback interface, enter the keyword
loopback
followed by a number from zero (0) to 16383.
842
Summary of Contents for Force10 Z9000
