background image

Back to Contents Page

  

 

 Replacing the CRT Board  

Dell™ Inspiron™ 1210 Service Manual 

 

 

 

 

 

 

1.

Follow the instructions in 

Before You Begin

.  

 

 

  

2.

Remove the palm rest. See 

Replacing the Palm Rest

.  

 

  

 

 

3.

Remove the M2.5x3-mm screw that secure the CRT board to the base of the computer.  
 

 

  

4.

Lift the CRT board up and out from the base of the computer.  
 

 

  

5.

To replace the CRT board, align the holes on the CRT board to the protrusions on the base of the computer.  
 

 

  

6.

Replace the CRT M2.5x3-mm screw to secure the CRT board to the base of the computer.  
 

 

  

7.

Replace the palm rest. See 

Replacing the Palm Rest

.  

 

 

  

8.

Slide the battery into the battery bay, until it clicks in place and slide the battery-lock latch towards the lock position.  
 

Back to Contents Page

 

 

 

 

CAUTION: 

Before working inside your computer, read the safety information that shipped with your computer. For additional safety best 

practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.

 

NOTICE: 

To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such 

as a connector on the back of the computer).

CRT board 

M2.5x3-mm screw 

Summary of Contents for Inspiron 1210







































Reviews: