background image

Removing 

the 

Coin-Cell 

Battery  |  

63

25

Removing the Coin-Cell Battery

 

WARNING:  Before working inside your computer, read the safety information 
that shipped with your computer and follow the steps in "Before You Begin" on 
page 7. After working inside your computer, follow the instructions in "After 
Working Inside Your Computer" on page 9. For additional safety best practices 
information, see the Regulatory Compliance Homepage at dell.com/
regulatory_compliance.

 

WARNING:  The battery may explode if installed incorrectly. Replace the battery 
only with the same or equivalent type. Discard used batteries according to the 
manufacturer’s instructions.

 

CAUTION: Removing the coin-cell battery resets the BIOS settings to default. It is 
recommended that you note the BIOS settings before removing the coin-cell 
battery.

Prerequisites

1

Remove the memory module(s). 

 

See "Removing the Memory Module(s)" on page 11.

2

Remove the optical drive. 

 

See "Removing the Optical-Drive Assembly" on page 15.

3

Remove the keyboard. See "Removing the Keyboard" on page 19.

4

Remove the palm-rest assembly. 

 

See "Removing the Palm-Rest Assembly" on page 25.

5

Remove the battery. See "Removing the Battery" on page 31.

6

Remove the hard drive. See "Removing the Hard Drive" on page 35.

7

Remove the wireless Mini-Card. 

 

See "Removing the Wireless Mini-Card" on page 39.

8

Follow the instructions from step 1 to step 4 in "Removing the System Board" on 
page 57.

OM_Book.book  Page 63  Tuesday, October 16, 2012  11:59 AM

Summary of Contents for Inspiron 14Z 5423































































































Reviews: