background image

Before working inside your 

computer

CAUTION: To avoid damaging the components and cards, handle 
them by their edges and avoid touching pins and contacts.

NOTE: The images in this document may differ from your computer 
depending on the configuration you ordered.

 

Before you begin 

Save and close all open files and exit all open applications.

Shut down your computer.

– Windows 8.1: On the 

Start

 screen, click or tap the power icon 

 → 

Shut down

.

– Windows 7: Click or tap 

Start 

→ 

Shut down

.

NOTE: If you are using a different operating system, see the 
documentation of your operating system for shut-down 
instructions.

Disconnect your computer and all attached devices from their electrical 

outlets.

Disconnect all cables such as telephone cables, network cables and so 

on, from your computer.

Disconnect all attached devices and peripherals, such as keyboard, 

mouse, monitor, and so on, from your computer.

Remove any media card and optical disc from your computer, if 

applicable.

After the computer is unplugged, press and hold the power button for 5 

seconds to ground the system board.

CAUTION: Place the computer on a flat, soft and clean surface to 
avoid scratching the display.

Place the computer face down.

8

Summary of Contents for Inspiron 24 3000 series
















































































Reviews: