background image

3–Fibre Channel Configuration
Setting Fibre Channel Adapter Parameters

42

CU0354604-00  P

Verify the disk data (Some targets do not support this feature.) 

Select a disk device

Loopback Data Test

The 

Loopback Data Test

 option allows you to perform the following loopback 

tests:

External loopback data test

Internal loopback data test

Select Adapter

If you have a multiport or multiple 2600 Series Adapters in the system, use the 

Select Adapter

 option to select and then configure or view the settings of a 

specific 2600 Series Adapter or one of its ports.

Exit 

Fast!

UTIL

The 

Exit 

Fast!

UTIL option allows you to exit the utility and reboot the system. 

After making changes to the 2600 Series Adapter in 

Fast!

UTIL, make sure you 

save the changes before you reboot the system.

Setting Fibre Channel Adapter Parameters

Use QConvergeConsole to set Fibre Channel adapter parameters:

Setting Fibre Channel Adapter Parameters with QConvergeConsole GUI

Setting Fibre Channel Adapter Parameters with Interactive 
QConvergeConsole CLI

Setting Fibre Channel Adapter Parameters with Noninteractive 
QConvergeConsole CLI

CAUTION

Performing a low-level format destroys all data on the disk.

NOTE

When running an external loopback data test, make sure that the Fibre 
Channel link is up or a loopback plug is attached to the 2600 Series Adapter 
before starting the test. 

Summary of Contents for MARVELL QLogic QLE2660-DEL

































































































































































Reviews: