background image

Table 38. Supported hardware components (continued)

Hardware component

V570 and V570F

P570 and P570F

S570

Customer

Replaceable

Unit (CRU)

Field

Replaceable

Unit (FRU)

Customer

Replaceable

Unit (CRU)

Field

Replaceable

Unit (FRU)

Customer

Replaceable

Unit (CRU)

Field

Replaceable

Unit (FRU)

System Motherboard

No

Yes

No

Yes

No

Yes

Host Bus Adapter
(HBA330)

No

Yes

No

Yes

No

Yes

BOSS controller card
and M.2 SATA disk

No

Yes

No

Yes

No

Yes

Network Daughter Card
(NDC)

No

Yes

No

Yes

No

Yes

NOTE:

 The preceding table provides a non-exhaustive list of FRUs that reflects the common top-level assembly parts.

System memory

The appliance supports DDR4 registered DIMMs (RDIMMs) and load reduced DIMMs (LRDIMMs). System memory holds the
instructions that are executed by the processor.

NOTE:

 MT/s indicates DIMM speed in MegaTransfers per second.

Memory bus operating frequency can be 2666 MT/s, 2400 MT/s, or 2133 MT/s depending on the following factors:

DIMM type (RDIMM or LRDIMM)

Number of DIMMs populated per channel

System profile selected (for example, Performance Optimized, or Custom [can be run at high speed or lower])

Maximum supported DIMM frequency of the processors

Your appliance contains 24 memory sockets split into two sets of 12 sockets, one set per processor. Each 12-socket set is
organized into six channels. In each channel, the release tabs of the first socket are marked white, and the second socket black.

34

Replacing and adding hardware

Summary of Contents for P570






































Reviews: