Dell PowerConnect W AirWave 7.1
| User Guide
Configuring AWMS |
69
2. If the AP is the Primary or Backup WDS, select
Use the AP as Wireless Domain Services
.
Select
Priority
(set
200
for Primary,
100
for Secondary).
Configure the
Wireless Network Manager
(configure the IP address of WLSE).
3. If the AP is Member Only, leave all options unchecked.
4. Navigate to the
Security > Server Manager
page.
5. Enter the
IP address
and
Shared Secret
for the ACS server.
6. Click the
Apply
button.
7. Navigate to the
Wireless Services > WDS > Server Group
page.
8. Enter the WDS Group of AP.
9. Select the
ACS server
in the
Priority 1
drop- down menu.
10. Click the
Apply
button.
Configuring ACS for WDS Authentication
ACS authenticates all components of the WDS and must be configured first. Perform these steps to make this
configuration.
1. Login to the ACS.
2. Navigate to the
System Configuration > ACS Certificate Setup
page.
3. Install a New Certificate by clicking the
Install New Certificate
button, or skip to the next step if the
certificate was previously installed.
4. Click the
User Setup
button in the left frame.
5. Enter the
Username
that will be used to authenticate into the WDS and click
Add/Edit
button.
6. Enter the
Password
that will be used to authenticate into the WDS and click the
Submit
button.
7. Navigate to the
Network Configuration > Add AAA Client
page.
8. Add
AP Hostname
,
AP IP Address
, and
Community String
(for the key).
9. Enter the
Password
that will be used to authenticate into the WDS and click the
Submit
button.
For additional and more general information about ACS, refer to
“Configuring ACS Servers” on page
71
.
Configuring Cisco WLSE Rogue Scanning
The
AMP
Setup > WLSE
page allows AWMS to integrate with the Cisco Wireless LAN Solution Engine
(WLSE). AWMS can discover APs and gather rogue scanning data from the Cisco WLSE.
Figure 33
illustrates and itemizes the AWMS settings for communication that is enabled between AWMS and
WLSE.
Figure 33
AMP Setup > WLSE > Add WLSE
Page Illustration
Perform the following steps for optional configuration of AWMS for support of Cisco WLSE rogue scanning.
Summary of Contents for PowerConnect W Airwave 7.1
