background image

22

        |       About your monitor

• 

When lifting or moving the monitor, do not turn the monitor upside down while 
holding the stand base or stand riser. This may result in accidental damage to the 
monitor or cause personal injury.

Maintenance guidelines

Cleaning your monitor

 CAUTION: Read and follow the 

Safety instructions

 before cleaning the 

monitor.

 WARNING: Before cleaning the monitor, unplug the monitor power cable 

from the electrical outlet.

For best practices, follow the instructions in the list below when unpacking, cleaning, 
or handling your monitor:

• 

To clean your anti-static screen, lightly dampen a soft, clean cloth with water. If 
possible, use a special screen-cleaning tissue or solution suitable for the anti-
static coating. Do not use benzene, thinner, ammonia, abrasive cleaners, or 
compressed air.

• 

Use a lightly-dampened, warm cloth to clean the monitor. Avoid using detergent 
of any kind as some detergents leave a milky film on the monitor.

• 

If you notice white powder when you unpack your monitor, wipe it off with a 
cloth.

• 

Handle your monitor with care as a darker-colored monitor may get scratched 
and show white scuff marks more than a lighter-colored monitor.

• 

To help maintain the best image quality on your monitor, use a dynamically  
changing screen saver and turn off your monitor when not in use.

Summary of Contents for S2421H


























































Reviews: