background image

About your monitor 

  23

• When lifting or moving the monitor, do not turn the monitor upside down while 

holding the stand base or stand riser. This may result in accidental damage to 
the monitor or cause personal injury.

Maintenance guidelines

Cleaning your monitor

CAUTION: Read and follow the 

Safety instructions

 before cleaning the 

monitor.

WARNING: Before cleaning the monitor, unplug the monitor power 
cable from the electrical outlet.

For best practices, follow the instructions in the list below when unpacking, 
cleaning, or handling your monitor:

• To clean your anti-static screen, lightly dampen a soft, clean cloth with water. 

If possible, use a special screen-cleaning tissue or solution suitable for the 
anti-static coating. Do not use benzene, thinner, ammonia, abrasive cleaners, 
or compressed air.

• Use a lightly-dampened, warm cloth to clean the monitor. Avoid using 

detergent of any kind as some detergents leave a milky film on the monitor.

• If you notice white powder when you unpack your monitor, wipe it off with a 

cloth.

• Handle your monitor with care as a darker-colored monitor may get scratched 

and show white scuff marks more than a lighter-colored monitor.

• To help maintain the best image quality on your monitor, use a dynamically 

changing screen saver and turn off your monitor when not in use.

Summary of Contents for S2421HGF



























































Reviews: