background image

Dell Networking W-IAP277 Outdoor Instant Access Point

| Installation Guide

13

EU Regulatory Conformance 

Dell, hereby declares that the APEX0102 device model is in compliance with the essential 

requirements and other relevant provisions of Directive 1999/5/EC -CE(!). The Declaration of Conformity made 
under Directive 1999/5/EC is available for viewing on 

dell.com.

Proper Disposal of Dell Equipment

For the most current information about Global Environmental Compliance and Dell products, visit 

dell.com

.

Waste of Electrical and Electronic Equipment

Dell products at end of life are subject to separate collection and treatment in the EU 
Member States, Norway, and Switzerland and therefore are marked with the symbol shown at 
the left (crossed-out wheelie bin). The treatment applied at end of life of these products in 
these countries shall comply with the applicable national laws of countries implementing 
Directive 2002/95/EC on Waste of Electrical and Electronic Equipment (WEEE).

European Union RoHS

Aruba Networks Inc., hereby, being the manufacturer of this product, declares that all CE 

marked Dell wireless controller and access point products are manufactured in accordance 

to the provisional requirements set forth in the RoHS Directive 2011/65/EC.

A copy of the Aruba Declaration of Conformity may be obtained upon request from:
Aruba Networks International Ltd.

Building 1000, 

Citygate Mahon 

Cork Ireland
Please include the regulatory model number located on the product’s regulatory nameplate with the request.

China RoHS

Dell products also comply with China environmental declaration requirements and are labeled 
with the “EFUP 10” label shown at the left.

10

᳝↦᳝ᆇ⠽䋼ໄᯢ

Hazardous Materials Declaration

᳝↦᳝ᆇ⠽䋼៪ܗ㋴

(Hazardous Substance) 

䚼ӊৡ⿄

(Parts) 

3E

+J

&G

݁Ӌ䫀

&U

໮⒈㘨㣃

3%%

໮⒈Ѡ㣃䝮

3%'(

⬉䏃ᵓ

(

PCA Boards)

h

ƻ

ƻ

ƻ

ƻ

ƻ

ᴎẄ㒘ӊ

(

Mechanical Sub-Assemblies)

h

ƻ

ƻ

ƻ

ƻ

ƻ

ƻ˖ 㸼⼎䆹᳝↦᳝ᆇ⠽䋼೼䆹䚼ӊ᠔᳝ഛ䋼ᴤ᭭Ёⱘ৿䞣ഛ೼

SJ/T11363-2006

ᷛޚ㾘ᅮⱘ䰤䞣㽕∖ҹϟDŽ

Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts is 
below the relevant threshold of the SJ/T11363-2006 standard.

h˖ 㸼⼎䆹᳝↦᳝ᆇ⠽䋼㟇ᇥ೼䆹䚼ӊⱘᶤϔഛ䋼ᴤ᭭Ёⱘ৿䞣䍙ߎ6-7ᷛޚ㾘ᅮⱘ䰤䞣㽕∖DŽ

Indicates that the concentration of the hazardous substance of at least one of all homogeneous materials 
in the parts is above the relevant threshold of the SJ/T11363-2006 standard. 

ᇍ䫔ଂП᮹ⱘ᠔ଂѻકᴀ㸼ᰒ⼎կᑨ䫒ⱘ⬉ᄤֵᙃѻકৃ㛑ࣙ৿䖭ѯ⠽䋼DŽ

This table shows where these substances may be found in the supply chain of electronic information 

products, as of the date of sale of the enclosed product.   

ℸᷛᖫЎ䩜ᇍ᠔⍝ঞѻકⱘ⦃ֱՓ⫼ᳳᷛᖫᶤѯ䳊䚼ӊӮ᳝ϔϾϡৠⱘ⦃ֱՓ⫼ᳳ
՟བ⬉∴ऩܗ῵ഫ䌈೼݊ѻકϞ
ℸ⦃ֱՓ⫼ᳳ䰤া䗖⫼Ѣѻકᰃ೼ѻક᠟ݠЁ᠔㾘ᅮⱘᴵӊϟᎹ԰

The Environment- Friendly Use Period (EFUP) for all enclosed products and their parts are 
per the symbol shown here. The Environment- Friendly Use Period is valid only when the 
product is operated under the conditions defined in the product manual. 

Summary of Contents for W-IAP277

















Reviews: