17
16. "POSITION 2l CONTAINER" "OK TO START RINSING": Place
the container used to collect the descaler solution empty
under the hot water spout (fig. 9) and press
17. Hot water is delivered from the hot water/steam spout and
"RINSING UNDERWAY" "PLEASE WAIT" is displayed;
18. "EMPTY DRIP TRAY" (fig. 22): At the end of the second
rinse, remove, empty and replace the drip tray (A15) and
grounds container (A11) and press
;
19. "DESCALE COMPLETE": press
;
20. "FILL TANK WITH" "FRESH WATER": empty the container
used to collect the rinse water, remove the water tank and
fill with fresh water up to the MAX level, then put back in
the appliance.
The descaling cycle is now complete.
Please note!
• If the descaling cycle is not completed correctly (e.g. no
electricity) we recommend repeating the cycle;
• After descaling, it is normal for the grounds container
(A11) to contain water.
• If the water tank has not been filled to the MAX level, at
the end of descaling, the appliance requests a third rinse to
guarantee that the descaler solution has been complete-
ly eliminated from the machine's internal circuits. Before
starting rinsing, remember to empty the drip tray;
• The appliance may request descaling cycles at very short
intervals. This is normal and due to the appliance’s ad-
vanced control system.
15.
SETTING WATER HARDNESS
The "DESCALING NEEDED" "PRESS OK TO START (~45MIN)
" message is displayed after a period of time established
according to water hardness.
The machine is set by default for a hardness value of "4". The
machine can also be programmed according to the hardness
of the mains water in the various regions so that the machine
needs to be descaled less often.
15.1 Measuring water hardness
1. Remove the TOTAL HARDNESS TEST indicator paper (D1)
from its pack (attached to the English instructions).
2. Immerse the paper completely in a glass of water for one
second.
3. Remove the paper from the water and shake lightly. After
about a minute, 1, 2, 3, or 4 red squares form, depending
on the hardness of the water. Each square corresponds to
one level.
Indicator paper
Water hardness
Level 1 - soft water
Level 2 - slightly hard
water
Level 3 - hard water
Level 4 - very hard water
15.2 Setting water hardness
1. Access the menu as described in section "6.1 Access the
settings menu";
2. Press "WATER HARDNESS";
3. "WATER HARDNESS" "CURRENT VALUE UNDERLINED": Press
the required level (Level 1 = soft water; Level 4 = very hard
water);
4. Press "
" to go back to the homepage.
The machine is now reprogrammed with the new water hard-
ness setting.
16.
WATER SOFTENER FILTER
Certain models are fitted with a water softener filter (D4). If this
is not the case with your model, you are recommended to pur-
chase one from De’Longhi Customer Services.
To use the filter correctly, follow the instructions below.
16.1 Installing the filter
1. Remove the filter (D7) from the packaging;
2. Access the menu as described in section "6.1 Access the
settings menu";
3. Press "WATER FILTER"; "TURN DATE INDICATOR TO NEXT 2
MONTHS" (fig. 37): turn the date disk to display the next
2 months of use.
4. Press
;
37
38
Summary of Contents for Dinamica Plus ECAM37X.95
Page 1: ...De Longhi Appliances via Seitz 47 31100 Treviso Italy www delonghi com 5713238071_00 _0718 ...
Page 4: ...3 A A2 A1 A5 A4 A3 A6 A7 A22 A21 B C A8 A9 A12 A17 A18 A11 A10 A14 A15 A13 A16 A20 A19 ...
Page 5: ...4 4 3 3 1 7 6 5 12 9 15 MILK 10 13 1 2 11 16 14 8 ...
Page 6: ...5 25B 25A 27 17 31 30 21 19 28 26 29 P U S H 22 24 P U S H P U S H CLEAN 18 20 23 32 ...
