background image

EN

6

7

1/  Motor fitting .................................................................................................8

1.1  Crown and wheel assembly ................................................................................. 8
1.2  Assembly in the tube ............................................................................................... 8
1.3  Motor head position ................................................................................................ 9
1.4  Attaching the motor to the mount .................................................................... 9

2/ Connection ................................................................................................10

2.1  Wiring without push button, only by transmitter .................................. 10
2.2  Wiring with a push button ................................................................................. 10

3/  Starting up for the first time ...............................................................11

3.1. Associating.the.first.remote.control.to.a.motor

 ...................................... 11

3.2  Setting stops ............................................................................................................. 12

4/  Modifying stops  ......................................................................................16

5/  Associating another transmitter .......................................................16

6/  Associating a smoke detector ............................................................17

7/  Grouped command .................................................................................17

8/  Remove one or several associations ................................................18

8.1  Remove an association ........................................................................................ 18
8.2  Remove all associations ...................................................................................... 18

9/  Obstacle detection .................................................................................19

10/  Factory reset  .........................................................................................19

11/  Favourite positions ..............................................................................20

12/  Association with an alarm control unit ........................................21

12.1 Associating the motor intruder mode with the alarm control unit 21

12.2.Defining.the.motor’s.operating.mode.

 ......................................................... 22

13/  Your remote control is lost or not functioning..........................23

14/ Help ............................................................................................................24

15/  Technical Characteristics ..................................................................25

Contents

Summary of Contents for TYMOOV PERFORMANCE DXRP















Reviews: