background image

 

SPBD-155E4J1RT

 

DELTA ELECTRONICS, INC.

 

6 Revision: 

S1

09/20/2006

www.deltaww.com

 

7. Pin Description 
 

 

SFP Transceiver Electrical Pad Layout

   

                 

   

Host Board Connector Pad Layout

 

 

 

Pin Function Definitions 

Pin Num. 

Name 

Function 

Plug Seq.

Notes 

1 VeeT 

Transmitter 

Ground 

1  Note 

(1) 

TX Fault 

Transmitter Fault Indication 

Note (2) 

3 TX 

Disable 

Transmitter 

Disable 

3  Note 

(3) 

MOD-DEF2  Module Definition 2 

Note (4), 2 wire serial ID interface 

MOD-DEF1  Module Definition 1 

Note (4), 2 wire serial ID interface 

MOD-DEF0  Module Definition 0 

Note (4), Grounded in Module 

Rate Select 

Not Connect 

Function not available 

LOS 

Loss of Signal 

Note (5) 

9 VeeR 

Receiver 

Ground 

1   

10 VeeR 

Receiver 

Ground 

1   

11 VeeR 

Receiver 

Ground 

1   

12 

RD- 

Inv. Received Data Out 

Note (6) 

13 

RD+ 

Received Data Out 

Note (6) 

14 VeeR 

Receiver 

Ground 

1   

15 VccR 

Receiver 

Power 

2  Note 

(7) 

16 VccT 

Transmitter 

Power 

2  Note 

(7) 

17 VeeT 

Transmitter 

Ground 

1   

18 

TD+ 

Transmit Data In 

Note (8) 

19 TD- 

Inv. 

Transmit 

Data 

In 

3  Note 

(8) 

20 VeeT 

Transmitter 

Ground 

1   

Plug Seq.: Pin engagement sequence during hot plugging. 

Summary of Contents for SFP Bi-Directional Transceiver Module SPBD-155E4J1RT












Reviews: