background image

5-ENG

D25235

HOW TO PREVENT IT

WHAT CAN HAPPEN

WARNING: Risk to Breathing

WARNING: Risk of Electrical Shock

HOW TO PREVENT IT

WHAT CAN HAPPEN

HAZARD

HAZARD

Your 

air compressor is powered by

electricity. 

Like any other electrically

powered device, 

If it is not used properly

it may cause electric shock.

Repairs 

attempted 

by unqualified per-

sonnel can result in serious injury or
death by electrocution.

Electrical Grounding: 

Failure to provide

adequate grounding to this product
could result in serious injury or death
from electrocution. 

See grounding instructions.

Never operate

the compressor 

outdoors

when it is raining or in wet conditions.

Never operate compressor with protec-
tive covers removed

or damaged.

Any 

electrical wiring or repairs

required

on this product s

hould be performed by

authorized service center personnel

in

accordance with national and local electri-
cal codes.

Make certain that the electrical circuit

to which the compressor is connected

provides proper electrical grounding,
correct voltage and adequate fuse pro-
tection.

The 

compressed air

directly from your

compressor

is not safe for breathing

.

The

air stream may contain carbon

monoxide, toxic vapors, or solid parti-
cles

from the tank. 

Breathing 

these 

con-

taminants can cause serious injury or
death

.

Sprayed materials 

such as paint, paint

solvents, paint remover, insecticides,
weed killers, may 

contain harmful vapors

and poisons.

Air 

obtained directly from the compressor

should never be used to supply air for
human consumption.

In order to use air

produced by this compressor for breath-
ing, suitable 

filters and

in-line 

safety

equipment must be properly installed.

In-line 

filters and safety equipment 

used

in conjunction with the compressor 

must

be capable of treating air to all applica-
ble local and federal codes prior to
human consumption.

Work in an area with good cross venti-
lation. 

Read and

follow the safety

instructions 

provided on the label or

safety data sheets

for the materials you

are spraying. Use a NIOSH/ MSHA
approved respirator 

designed for use

with your specific application.

Summary of Contents for OILLUBE AIR COMPRESSOR D25235 029-2































Reviews: