background image

6

10. Do not disassemble charger or battery pack.

Take it to a qualified ser-

viceman when service or repair is required. Incorrect reassembly may result in
a risk of electric shock or fire.

11. Unplug charger

from outlet before attempting any maintenance or clean-

ing – to reduce risk of electric shock.

12. Charge the battery pack

in a well ventilated place, do not cover the

charger and battery pack with a cloth, etc., while charging.

13. Do not store

the charger or battery pack in locations where the temper-

ature may reach or exceed 122°F (50°C) (such as a metal tool shed, or a car
in the summer), which can lead to deterioration of the storage battery.

14. Do not charge battery pack

when the temperature is BELOW 40°F

(4.4°C) or ABOVE 104°F(40°C). This is very important for proper operation.

15. Do not incinerate battery pack.

It can explode in a fire.

16. Do not charge battery

in damp or wet locations.

17. Do not attempt

to charge any other cordless tool or battery pack with the

Delta charger.

18. Do not short across

the terminals of the battery pack: EXTREMELY

HIGH TEMPERATURES COULD CAUSE PERSONAL INJURY OR FIRE.

19.  Double insulated tools are equipped with a polarized plug (one blade
is wider than the other). This plug will fit in a polarized outlet only one
way. If the plug does not fit fully in the outlet, reverse the plug. If it still
does not fit, contact a qualified electrician to install a polarized outlet. Do
not change the plug in any way.

Double Insulation

eliminates the need

for the three wire grounded power cord and grounded power supply system.

20. Dispose of expended batteries properly.

The

Delta Battery Packs contains rechargeable, nickel-cad-
mium batteries. These batteries must be recycled or
disposed of properly. Drop off expended battery packs
at your local replacement battery retailer, your local
recycling center, or at a Delta Service Center (see list on
back page of this manual). Applicable fees for the col-
lection and recycling of these batteries (in the United
States), have been paid to the RBRC

. For further infor-

mation, call: 1-800-8-BATTERY. 

REPLACEMENT PARTS

When servicing use only identical replacement parts.

RBRC™ is a Trademark of
the Rechargeable Battery
Recycling Corporation.

FUNCTIONAL DESCRIPTION

FOREWORD

Delta Model CL180JS Cordless Jigsaw is designed to use Universal-Shank
Blades for cutting materials of the following MAXIMUM thickness: wood 4

1

/

3

",

plastic and fiberglass 1

1

/

4

", aluminum and nonferrous metals 

13

/

16

", mild steel

3

/

8

", and stainless steel 

1

/

8

".

CHARGING THE BATTERY

CHARGING THE BATTERY PACK GENERAL 

Before using your cordless tool for the first time, the battery pack should be
fully charged. If the battery pack is installed in the tool, remove it by following
instructions under INSTALLING OR REMOVING BATTERY PACK. 

Summary of Contents for ShopMaster CL180JS
















Reviews: