background image

I-951 

 

Page 1 of 8 

Rev. F-43693      2/14/2018 

DEMA D

ILUTION

-A

T

-H

AND

 

EXTREME

 

800 Series Chemical Dispensers 

 

   

   

   

   

 

 

 

Overview  

The DILUTION-AT-HAND 

EXTREME

 chemical dispenser series combines the proven technology 

of the DEMA DILUTION-AT-HAND with a new look and modular chemical enclosures. 
 
The dispenser series accurately dilutes chemical concentrates with water and dispenses the diluted 
mixture at either a high flow rate to fill buckets and scrubbers or a low flow rate to fill bottles and 
small containers. 
 
Each dispenser can be set up to meet specific application needs with the ability to offer: 
 

 

High and low flow dispensing 

 

2 Liter or 1 Gallon (5 Liter) chemical cabinets 

 

Selector valve option to dispense more than 
one chemical per dispensing unit 

 

Bottle filling or bucket filling 

 

Option of a remote gun for bucket or scrubber 
filling 

 

Dilution ratios up to 3:1 for low flow 
dispensing and up to 7:1 for high flow 
dispensing 

 

Supplied metering tips allow for leaner ratios 
of dilution 

 

 

Warnings 

 
 

All installations must conform to local plumbing codes and use approved backflow 
prevention devices.  A pressure indicating tee is to be installed with existing faucets 
according to local plumbing codes in the state of Wisconsin and any other state that 
requires the use of a pressure indicting tee. 
 

 

ALWAYS WEAR PROTECTIVE CLOTHING AND EYEWEAR WHEN 
WORKING WITH CHEMICAL PRODUCTS. 

 

 
 

Summary of Contents for 801GAP









Reviews: