background image

3

General safety precautions

WARNING!  When  using  electric 

tools, basic safety precautions should al-

ways be followed to reduce the risk of fire, 

electric shock and personal injury, includ-

ing the following.

Read all these instructions before operat-

ing  this  product  and  save  these  instruc-

tions.

For safe operations: 

1. Keep work area clean. Cluttered areas 

and benches invite injuries.

2.  Consider  work  area  environment.  Do 

not  expose  power  tools  to  rain.  Do  not 

use power tools in damp or wet locations. 

Keep work area well lit. Do not use power 

tools  where  there  is  risk  to  cause  fire  or 

explosion.

3.  Guard  against  electric  shock.  Avoid 

body  contact  with  earthed  or  grounded 

surfaces. (e.g. pipes, radiators, ranges, re-

frigerators).

4. Keep children and infirm persons away. 

Do not let visitors touch the tool or exten-

sion cord. All visitors should be kept away 

from work area.

5. Store idle tools. When not in use, tools 

should be stored in a dry, high or locked 

up place, out of reach of children and in-

firm persons.

6. Do not force the tool. It will do the job 

better and safer at the rate for which it was 

intended.

7. Use the right tool. Do not force small 

tools  or  attachments  to  do  the  job  of  a 

heavy duty tool. Do not use tools for pur-

poses not intended.

8.Dress properly. Do not wear loose cloth-

ing or jewelry; they can be caught in mov-

ing  parts.  Rubber  gloves  and  non-skid 

footwear are recommended when working 

outdoors. Wear protecting hair covering to 

contain long hair.

9. Use eye protection. Also use face or dust 

mask if the cutting operation is dusty.

10. Connect dust extraction equipment. If 

devices  are  provided  for  the  connection 

of dust extraction and collection facilities 

ensure  these  are  connected  and  properly 

used.

11. Do not abuse the cord. Never carry the 

tool by the cord or yank it to disconnect it 

from the receptacle. Keep the cord away 

from heat, oil and sharp edges.

12. Secure work. Use clamps or a vise to 

hold the work. It is safer than using your 

hand  and  it  frees  both  hands  to  operate 

tool.

13. Do not overreach. Keep proper footing 

and balance at all times.

14.  Maintain  tools  with  care.  Keep  cut-

ting tools sharp and clean for better and 

safer  performance.  Follow  instructions 

for lubrication and changing accessories. 

Inspect  tool  cords  periodically  and  if 

damaged,  have  it  repaired  by  authorized 

service center. Inspect extension cords pe-

riodically and replace, if damaged. Keep 

handles dry, clean, and free from oil and 

grease.

15. Disconnect battery charger. When not 

in use, before servicing and inspection.

16. Disconnect tool. When not in use, be-

fore servicing and before changing the ac-

cessories. 

17. Remove adjusting keys and wrenches. 

Form the habit of checking to see that keys 

and adjusting wrenches are removed from 

the tool before turning it on.

18. Avoid  unintentional  starting.  Do  not 

carry a plugged in tool with a finger on the 

switch.  Ensure  switch  is  off  when  plug-

ging in.

19.  Use  outdoor  extension  leads.  When 

Summary of Contents for Zenit Powertools CD-18 E









Reviews: