background image

20 

 

 
 
 
 
 
 
 
 
 

Hesitation, dead 

spot or stalling that 

only seems to 

occur after the first 

mile of warm-up. 

1) Defective electric assist on 
choke 

1) Replace it. 

2) Defective accelerator pump 
(low output). 

2) Replace it. 

3) Float level setting very low. 

3) Adjust to factory specs.  Factory setting, with air horn upside 
down, is 1.01”+/- .015” from the cast surface to bottom of float. 

Compression or 

Misfiring 

1) Run a compression check. 

1) This will isolate bad rings, or valves, worn cylinder walls, 
defective cylinder head or gaskets and excessive carbon 
deposits. 

2) Check dwell variations. 

2) Check at variable speeds for excessive distributor shaft wear, 
faulty 

 

For further questions, please contact our technical department at 1-270-901-3346. 

 

Demon Carburetion™ Limited Warranty 

 

All Demon Carburetion™ Limited Warranties are extended to the original consumer only. This Limited Warranty is not 
assignable or otherwise transferable. There are no warranties that extend beyond those stated herein. Demon 
Carburetion™ offers no other warranties expressed or implied beyond this Limited Warranty.  
 
In the event of an alleged defect in material or workmanship, the responsibility of 

Demon Carburetion™ is strictly limited to 

the repair or replacement of the defective product. Demon C

arburetion™ has no other obligation expressed or implied. 

Final warranty determination will be in the sole discretion of 

Demon Carburetion™. Demon Carburetion™ shall not be 

responsible for; (a) actual or alleged labor, transportation, or other incidental charges; or (b) actual or alleged 
consequential or other damages incurred by use of any product of 

Demon Carburetion™.  

 
To initiate the warranty process, the consumer must return the alleged defective product to the place of purchase with a 
dated receipt and completed applicable warranty claim tag. Warranty claims will be rejected if the date of purchase cannot 
be established by the consumer. Do not send products directly to 

Demon Carburetion™. Demon Carburetion™ assumes 

no responsibility for products sent directly to 

Demon Carburetion™.  

 
This Limited Warranty sets forth specific legal rights. The consumer may have other rights as a result of variations in state 
laws or provincial laws. This Limited Warranty supersedes all prior warranty statements.  

 
DEMON CARBURETION

™ – NEW PRODUCT 

 

 
Demon Carburetion™ warrants its new products to be free from defects in material and workmanship for a period of 90 
days from date of purchase.  
 
Demon Carburetion™ Limited Warranty specifically does not apply to products, which have been (a) modified or altered in 
any way; (b) subjected to adverse conditions, such as misuse, neglect, accident, improper installation or adjustment, dirt 
or other contaminants, water, corrosion, or faulty repair; or (c) used in other than those applications recommended by 
Demon Carburetion™. Demon Carburetion™ also does not warrant, and disclaims all liability for products used in racing 
activities and/or applications other than those specifically recommended in the current brand catalog.  

 

NOTE:   IF YOU HAVE ANY QUESTIONS ABOUT THE SETUP OR TUNING OF THIS CARBURETOR, PLEASE 

CONTACT THE DEMON CARBURETOR™ TECHNICAL DEPARTMENT DIRECTLY AT 270-901-3346. 

 

Return Address & Contact information: 

Demon Carburetion™ 

1801 Russellville Road 

Bowling Green, KY 42101 

270-901-3346 

www.demoncarbs.com 

 

© 2012 

Demon Carburetion™  All rights reserved. 

LIT701

 

Revision Date:  1-8-16 

Summary of Contents for 625 Street Demon Carburetor 1900





















Reviews: