background image

 

 

 

 

© DENAFRIPS CO. LTD. & VINSHINE AUDIO PTE. LTD. (SINGAPORE)  

ALL RIGHTS RESERVED 

3.

 

OPERATING INSTRUCTION 

3.1

 

Quick Start Guide 

 

Package Contents 

 

AVATAR CDT 

 

Disc Clamp 

 

Remote Control 

– 

CR2032 battery is required

 

 

Disc Loading 

To open the AVATAR top loading door, slide the lid towards the rear of the unit fully. The 
CDM4 assembly shall be visible, and the Disc Clamp shall be accessible.  

Lift the Disc Clamp gently by holding the centre part of the Disc Clamp. Place a disc to the 
centre of the disc holder. Place the Disc Clamp in the centre of the disc and disc holder.  

The Disc Clamp is magnetic, once it is in position with the centre of the CDM4 spinner, you 
should feel the grip. Please note that the Disc Clamp must be in the correct position for the 
CDT to be operational. 

Slide the top loading lid towards the front of the unit fully. The micro limit switch must be 
triggered for the CDT to be operational. 

 

Change Disc 

It is recommended to stop playing the current disc before changing the disc. This allow the 
CDM4 mechanism motor to stop spinning gradually. Press Stop button on the front panel to 
stop playing the current disc. 

Slide the top loading lid towards the rear of the unit fully. Retrieve the Disc Clamp and Disc 
gently. Follow the same steps stated in Disc Loading above. 

 

 

 

Summary of Contents for AVATAR













Reviews: