Get
ting Star
ted
Connections
Remot
e Contr
ol
Inf
or
mation
Tr
oubleshooting
Specifications
ENGLISH
Multi-Zone
Set
tings
Adjusting the Sound Field Effect (Parameter)
Setting items
Setting contents
Front Height
Set whether or not to use
the front height channel.
ON :
Use the front height channel.
OFF :
Do not use the front height channel.
This can also be set by pressing
.
Subwoofer ATT
Attenuate subwoofer level
when using EXT. IN mode.
ON :
The input from the subwoofer channel is attenuated.
OFF :
The input from the subwoofer channel is not attenuated. Usually use
in this mode.
Set this to “ON” if the subwoofer channel level seems too high when
playing audio signal.
Subwoofer
Turn subwoofer output on
and off.
ON :
The subwoofer is used.
OFF :
The subwoofer is not used.
Default
Restores all the surround
parameter settings to their
defaults.
Yes :
Reset to the defaults.
No :
Do not reset to the defaults.
Setting items
Setting contents
Tone Control
Sets the tone control function
ON and OFF.
This can be set when
“Dynamic EQ” (
v
page
47) is set to “OFF”.
ON :
Allow tone adjustment (treble, bass).
OFF :
Playback without tone adjustment.
The tone cannot be adjusted when in the DIRECT mode.
Bass
Adjusts the low frequencies.
This can be set when
“Tone Control” is set to
“ON”.
–6dB ~ +6dB (0dB)
Treble
Adjusts
the
high
frequencies.
This can be set when
“Tone Control” is set to
“ON”.
–6dB ~ +6dB (0dB)
Adjusting the tone (Tone Control)
Default settings are underlined.
Setting items
Setting contents
MultEQ
Corrects
the
frequency
response of the different
speakers.
NOTE
•
“MultEQ” and “Manual
EQ” settings for which
“Not Used” has been set at
“EQ Customize” (
v
page
29) cannot be selected.
• When using headphones,
“MultEQ” is set to “OFF”.
Audyssey :
Optimize frequency response of all speakers.
Audyssey Byp.L/R :
Optimize frequency response of speakers except
front L and R speakers.
Audyssey Flat :
Optimize frequency response of all speakers to flat
response.
Manual :
Apply frequency response set with “Manual EQ” (
v
page 47).
OFF :
The “MultEQ” equalizer cannot be used.
•
When “Audyssey”, “Audyssey Byp. L/R” or “Audyssey Flat” is
selected, “
” lights.
•
After running Audyssey Auto Setup, if the Speaker Configuration,
Distance, Channel Level, and Crossover Frequency have changed
without increasing the number of speakers measured, only “
” lights.
• This can also be set by pressing
.
Making the MultEQ, Dynamic EQ and Dynamic Volume
settings (Audyssey Settings)
Default settings are underlined.
•
When the “Audyssey Auto Setup” (
v
page 20) procedure is performed, the “MultEQ”, “Dynamic
EQ” and “Dynamic Volume” functions are enabled.
• Operating conditions for each function
• Dynamic EQ :
When “MultEQ” is set to “ON”
• Dynamic Volume :
When “Dynamic EQ” is set to “ON”
• Setting :
When “Dynamic Volume” is set to “ON”
NOTE
If the speaker settings are changed after the “Audyssey Auto Setup” procedure is performed,
“MultEQ”, “Dynamic EQ” and “Dynamic Volume” functions cannot be selected and “Run Audyssey”
is displayed.
If this happens, either perform the “Audyssey Auto Setup” procedure again, or perform the “Restore”
operation (
v
page 24) to restore the settings to as they were after the “Audyssey Auto Setup”
procedure was performed.
MultEQ
Dynamic EQ
Dynamic Volume
Setting
: Moves the cursor (Up/Down/Left/Right)
: Decision the setting
: Return to previous menu
Remote control
operation buttons
:
Displaying the menu
Cancel the menu
Pla
ybac
k
