background image

3. Starting detecting the point of failure

Check item(1).

Check the power supply status and communication status with the CPU of each device.

Start in HDMI Diagnostics mode and follow the procedures below.

(1) Start in HDMI Diagnostics mode

While the power is On, hold down buttons "

TUNER PRESET CH -

" and "

ZONE2 SOURCE

" for at least 

3 seconds.

HDMI DIAGNOSTICS

                "

HDMI DIAGNOSTICS

" is displayed.

When the mode has switched, start Hardware check.

Hardwarecheck...

             

(2-1) Display when an Error Code is displayed.

Err:    H1-XX      

                  Alternating display.

Contact support 

Check the Error Code table items.

Error Code table

Error Code

Check item No.

Description

H1-01

Check item (6)

Communication Error with HDMI Tx  

[U1039 : MN864788]

H1-02

Check item (11)

Communication Error with HDMI SW1   [U1000 : MN864788]

H1-03

Check item (16)

Communication Error with HDMI SW2   [U1003 : MN864788]

H1-04

Check item (29)

Communication Error with TMDS SW   [U1103 : TMDS261B]

H1-06

Check item (21)

Communication Error with GUI IC  

[U1026 : ADV8003]

H1-08

Check item (30)

Communication Error with DSP  

[U1073 : CS49844A]

H1-12

Check item (35)

Communication Error with DIR  

[U1040 : PCM9211]

H1-14

Check item (26)

DDR check Error    

 

[U1028, U1029 : A3R12E40DBF-8E]

H1-15

Check item (27)

Communication Error with GUI ROM  

[U1027 : W25Q128JVFIQ]

(2-2) Display when an Error is not detected.

1 Auto Test

Cancel the mode, and proceed to 

check item (2)

.

Canceling the selected mode

Press the power button to exit off the power.

Before Servicing 

This Unit

Electrical

Mechanical

Repair Information

Updating

93

Summary of Contents for AVR-S940H














































































































































































Reviews: