21
ENGLISH
Advanced version
Simple version
Information
Basic version
Changing the brightness of the display
( Dimmer control)
The brightness of the display can be changed.
Press
DIMMER
.
• The brightness changes each time the
button is pressed.
Normal
Dark
Dim
Off
Playing high-quality audio
( Pure direct function)
This enables you to play high quality audio by stopping the video
signal, etc., output, and outputting the analog audio signal only.
Press
PURE DIRECT
while stopped.
• The Pure Direct mode changes each time
the button is pressed.
Pure Direct1
Pure Direct2
Off
Pure Direct 1
This turns off the digital audio output, video output,
and display.
Pure Direct 2
This turns off the digital audio output and video
output.
Off
This turns off the pure direct function.
• You cannot use
PURE DIRECT
while the GUI menu is displayed.
• The pure direct setting returns to “Off” when the unit is put in
standby mode.
Basic settings
This section describes the setting operations for basic settings
available with the remote control.
The icons show the category of content applicable to each operation.
Video : Blu-ray Disc, DVD-Video, DivX plus HD,
MPEG, AVI, WMV, AVCHD
Audio : Super Audio CD, CD, DVD-Audio, MP3,
WMA, AAC, LPCM
Photo : JPEG
Basic connections
(
v
page 9)
Playback (Basic operation)
(
v
page 13)
n
Changing the brightness of the display
(Dimmer control)
(
v
page 21)
n
Playing high-quality audio
(Pure direct function)
(
v
page 21)
n
HDMI control functions
(
v
page 21)
n
Video resolution
(
v
page 22)
n
Adjusting the picture quality (Picture control)
(
v
page 23)
n
Mode setting
(
v
page 24)
HDMI control functions
When you make HDMI connections with a TV or AV receiver
compatible with this unit and HDMI control functions, you can perform
the following operations by setting up the HDMI control functions of
each device.
•
TV or AV receiver power is turned on by operating the unit and
functions change with this unit input.
•
Turning off the TV’s power turns the unit’s power to standby.
•
Operating the unit via the TV’s remote control.
(When the TV’s remote control has player operation buttons)
1
Set the HDMI control function to “On”.
GUI menu “System” – “HDMI Control” (
v
page 34).
2
Turn on all the equipment connected by HDMI cable.
3
Set the HDMI control function for all equipment
connected by HDMI cable.
• Please refer to the owner’s manuals of connected devices for how
to make settings.
• Carry out steps 2 and 3 if any of the equipment was unplugged.
4
To ensure that the unit’s HDMI video
output is
projected on the TV screen, change the input function
of the TV and AV receiver.
5
When you turn the TV’s power to standby, check
that the power of the unit and AV receiver also goes
on standby.
If the HDMI control function does not operate properly, check the
following points.
• Is the TV or AV receiver compatible with the HDMI control function?
• Are the HDMI control function settings of all equipment correct?
(Step 3)
• After setting, did you add another HDMI device connection or make
any changes in the connections? If so make the settings again.
NOTE
• Some functions may not operate depending on the connected TV
or AV receiver. Check the owner’s manual of each device for details
beforehand.
• When “HDMI Power Off Control” (
v
page 34) is set to “Off”, the
unit does not go to standby even if the connected device is in the
standby mode.
The icons show the category of
content applicable to each operation.
Video
Audio
Photo
For details of the media corresponding to each icon, see “Playable media”
(
v
page 45).
1.DBP1611E3_ENG_11A.indd 21
2011/07/23 10:40:00
