15
2.1. Version display
EFX SERECTOR is REVERB and press TAP button.
Display order
«_SYS»
→
«xxxx(system Ver.)»
→
«_dSP»
→
«xxxx(DSP Ver.)» ever 1 sec.
Press [EFX SEND / RETURN] button:Back to the Service Top.
2.2. LED Check
EFX SERECTOR is FLANGER and press TAP button.
Press TAP button to order, and the following mode.
q
All on
All LED (7SEG including) is lit (using LED lights do not light them all on at the same time)
w
DIM mode
All the lights DIM (DIM lines). Other (7SEG included) is off
DIM : EFX SEND(1~2), Monitor (1~2), EFX CUE, EFX ON, EFX SEND/RETURN, USB
e
All off
All LED (7SEG included) to full off.
r
Greeen lights up
Other Off (7SEG including.)
t
Umber lights up
Other Off (7SEG including.)
y
Red lights up
Other Off (7SEG including.)
u
Blue lights up
Other Off (7SEG including.)
i
7SEG lights up
«000.0» displayed. [BEAT> ]- Each time you press the button to count up.Other Off .
Count up«000.0»
→
«111.1»
→
«222.2»…
→
«999.9»
→
«000.0»
o
Max Load mode
Maximum light on the actual use. Power used to evaluate
MIC EFX INS, MAS EFX INS, AUX1 SELECT, SIG/PK(Red), DUCKING(Red) Lights other than those described to
the left.
Displayed «288.8».
Q0
TYP lights up mode
Immediately after assuming power. Power used to evaluate
ON : MASTER LEVEL, TAP, DRY/WET, BEAT(1), MIC SELECT
DIM : CH EFX SEND(1~2), Monitor (1~2), EFX CUE, EFX ON
Displayed «123.4».
Press [TAP] button :back to
q
.
Press [EFX SEND / RETURN] button:Back to the Service Top.
2.3. SW CHECK
• EFX SERECTOR is ECHO and press TAP button.
(1) Panel conduct the con
fi
rmation button. (17 total)
(2) First, displayed «__17»
(3) Initially, all the LED lights below.
MIC ON/OFF, DUCKING, AUX1, MIC EFX INS, SPLIT CUE, Monitor CH1, Monitor CH2, EFX SEND(CH1~CH2),
CH/MAS Meter SEL, MAS EFX INS, TAP, EFX CUE, EFX SEND/RETURN, EFX ON/OFF, BEAT(16,32)
(4)
Press the button corresponding to the button or LED, BEAT turns off the display unit. And to count the number that is
displayed.Do nothing when you press the button is the same.
(5) When you press the button all, «PASS» appears. Press EFX SEMD / RETURN button return to Service Top.
b
When you stop in the middle, press and hold the TAP button to return to the Service Top.
Summary of Contents for DN-X600
