Denon DRW-695, Operating Instructions Manual

6

ENGLISH

NAMES AND FUNCTIONS OF PARTS

q

Power Operation Switch (

¢

ON 

£

STANDBY)

• Press this once to turn the cassette deck’s power on. Press again to

set the cassette deck to the standby mode.

• The deck remains in a stand-by (non-operative) mode for

approximately 2 seconds after it is switched on.

i

Dubbing Speed Buttons (DUBBING SPEED)

• Pressing the NORMAL button starts regular speed dubbing from deck

A to deck B. Press the HIGH button to perform dubbing at double
speed. See page 10.

o

Bias Fine Control (BIAS FINE)

(For Normal, CrO

2

and Metal tape)

• Use this control to fine-adjust the bias. Standard bias is obtained at

the center click-stop position. See page 9.

!0

Input Level Control (INPUT LEVEL)

• This knob adjusts the recording input level. It affects the level in both

channels. See page 9.

!1

Tape Lighting

• The tape lighting makes it possible to clearly check the amount of

tape remaining.

!2

Cassette Compartment Cover

• If the cover is not closed completely, the tape transport buttons will

remain inoperative.

!3

Headphone Jack (PHONES)

• For private music enjoyment without disturbing others, or for

monitoring a recording, a headphone set may be connected to this
jack. Use a headphone with an impedance rating of 8 to 1200

Ω

/ohms.

!4

Remote Sensor (REMOTE SENSOR)

• With DRW-695 the remote control unit is not included.
• Each of “PLAY, FF, REW, STOP, REC PAUSE and REC/REC MUTE”

functions can be remote controlled with wireless handset of the
receiver (DRA Series receivers). For details refer to the DRA Series
operating instructions. 

NOTE:

Note that only the A deck can be operated with remote control units
which have no A/B selector button. 

!5

Timer Switch (TIMER)

• This switch is provided for use with an optional audio timer for

unattended recording or morning-alarm playback.

• For non-timer operation, this switch should be set in the “OFF”

position. See page 11.

Whenever the Power Operation switch is in the STANDBY state, the
apparatus is still connected on AC line voltage.
Please be sure to unplug the cord when you leave home for, say, a
vacation.

!6

Tape Transport Buttons

PLAY

2

6

7

4

REC/REC MUTE

(Deck B only)

3

REC PAUSE

(Deck B only)

0 1

Play Button

Stop Button

Fast Rewind Button

Fast Forward Button

Rec/Rec Mute

Button

Rec Pause Button

Direction Button

Press to playback tape.

Press to stop the tape in any mode.

Press for fast rewind.

Press for fast forwarding.

Press the REC/REC MUTE ( 

4

) button and PLAY button simultaneously to start recording. If only

the REC/REC MUTE ( 

4

) button is pressed, the deck enters the Recording Pause mode. Pressing

this button in the Recording Pause mode will start Auto Rec Mute, and a 5-second silent space is
recorded onto the tape. See page 9.

Press this button to enter the recording pause mode from the recording or recording mute mode.
This button can only be used during recording. See page 9.

Changes the tape transport direction from forward “

1

” to reverse “

0

” and vice versa.

w

Eject Button ( 

5

)

• Press this button to open the cassette compartment cover. When the

tape is running, press the STOP ( 

2

) button first to stop tape

transport, then press the Eject button.

e

Counter Reset Button (COUNTER RESET)

• Press this button to reset the tape counter to zero.

r

MPX Filter Button (MPX)

• The MPX FILTER button should be used to prevent interference with

the Dolby NR circuit when making Dolby NR encoded recordings of
FM stereo programs.

• When making Dolby NR encoded recordings from any program

source other than FM stereo, leave this button in the “OFF” position.

t

Counter Memory Button (MEMORY)

• When this button is pressed during forward tape travel ( 

), fast

rewinding ( 

6

) will stop automatically at the tape counter position

“

‚‚‚‚

”.

• When this button is pressed during reverse tape travel ( 

), fast

forwarding ( 

7

) will stop automatically at the tape counter position

“ 

‚‚‚‚

”. See page 11.

y

Dolby NR Switch (DOLBY NR)

• To record or playback tapes with Dolby B or C-type noise reduction,

set this switch to “B” or “C”. Turn it “OFF” when not using the
Dolby NR system.

u

Reverse Mode Switch (REV. MODE)

• Select the type of tape transport. The reverse mode can be set to

(one side), 

(continuous playback), RELAY (relay

playback).

Caution: