3. Connect the 12-way microfi t connector from the interface loom
to the CAR port of AVR.
4. Insert the 9 pin male DIN from the AVR into the GW500 iPod port.
5. Connect the iPod loom from the GW500 to the female 9 pin DIN
port on the AVR.
6. Remove the cable from the green Video-In Fakra connector
of the radio and connect it to the yellow Video-In phono of AVR
using the given Fakra-RCA converter cable.
7. Then connect the Video cable of “AV OUT TO HU” video output
from the 6-way microfi t back into the radio using the other Fakra-
RCA converter cable.
8. Connect all remaining connections (Rear Seat displays, DVD,
Cameras, handbrake detect etc.) as per section 4.
9. In some cases with the NTG1 vehicles there may not be a Quad
lock style connector on the rear of the head unit. In this case you
will need to use the universal harness for connectivity. (Universal
harness)
10. This 12 way micro-fi t connector consists on a 4 wire
installation.
11. Red -12V permanent power in, Black – Ground, Green – Reverse
gear detect (12v trigger), Red/White – Hand brake (neg trigger)
If you wish to use the factory TV-Tuner, please set the Gateway 500
to bypass mode. In this case all Gateway and AVR functionalites will
be disabled.
Depending on headunit capabilities the Video format of input/
output signals can be set to NTSC or PAL using a USB confi g fi le.
In most countries when the car is moving video is not permitted
by law on the head unit (this is the default, recommended
confi guration of AVR).
Pending local regulations and user liability, the Video in Motion
support may be enabled on AVR using a USB confi g fi le.
Please see more details on the USB confi guration fi les on the
Dension website.
4
Options
BMW
3
1. Carefully remove your vehicle’s head unit as per the factory
instructions and using the correct tools.
2. Connect the AVR interface loom between the head unit and the
vehicle harness.
3. Connect the 12-way microfi t connector from the interface loom
to the AVR.
4. Insert the 9 pin male DIN from the AVR into the GW500 iPod
port.
5. Connect the iPod loom from the GW500 to the female 9 pin DIN
port on the AVR.
6. On the 12-way microfi t harness there is a break out for the video
input in the vehicle. The Vehicle side will connect into the (yellow)
Video-In phono RCA input of AVR. The return video must be then
connected into the head unit harness. All connections are on the
supplied harness.
7. Connect all remaining connections (Rear Seat displays, DVD,
Cameras, handbrake detect etc.) as per section 4.
Introduction
Warning! Always make sure that your vehicle’s battery is
disconnected before beginning installation and that you have
your head unit’s (radio’s) security code (if applicable).
The Dension AVR will enable you to access audio and visual data from
a seperate, aftermarket source (iPod, DVD etc.) and view it on your
vehicle’s original head unit (radio) via a Gateway (GW) 500 module.
Please note that TV-Tuner activation may be required to enable the
AV input. Contact your dealer for more information. There are also
various options that will allow you to connect your aftermarket
source that would not be possible with the OE system (cameras/rear
seat entertainment etc.). Check the user guide for all functions.
All photos/illustrations are for representation purposes only and may diff er
visually from the equipment in your vehicle. Information correct at time of
going to print E. & O. E. Dension Audio Sytems Ltd. and it’s registered partners
cannot be held liable for any damages caused by the incorrect installation of
any Dension product.
Porsche
PCM2.1
Cayenne
n/a
2005-2008
Standard
AVRG5P1
CL
C215
2005-2006
CL
C216
2006-
CLS
W219
2004-
E
W211
2003-
S
W220
2003-2005
S
W221
2006-
SL
R230
2005-
SLK
R171
2004-
Universal Harness
A
W169
2005-
B
W245
2005-
C
W203
2004-2007
CLK
W209
2005-
G
W463
2005-
M
W164
2005-
R
V251
2006-
1 Series
E87
2004-
3 Series
E90/E91
2005-
BMW
5 Series
E60/E61
2004-
6 Series
E63/E64
2004-
7 Series
E65/E66
2004-
Class
HU
AVRG5M1
Product Part number
Loom required
MY
Type Code
AVRG5B1
Comand
NTG1
Comand
NTG2
Standard
i-Drive
CCC,8.8"
Professional
Standard
AVRG5M2
Mercedes
Standard
Standard
Universal Harness
Car compatibility
1
1. Carefully remove your vehicle’s head unit as per the factory
instructions and using the correct tools.
2. Connect the AVR interface loom between the head unit and the
vehicle harness.
Porsche and Mercedes
2
