background image

2.2 Battery Charging 

When you purchase the scanner, a battery has not been fully charged. You need to charge the battery using the 

dedicated Charging Cradle. Be sure to power off the scanner before charging. 

 
Charging the scanner 

●Charging time

 

It takes approximately for 3.5 hours for BT-180LA thin-type battery and 7 hours for BT-SP1L large capacity battery 

to charge a battery to full. This charging time is a standard time when the temperature is at 25°C and it may vary 

according to the condition of operation. 

 

Connect the output plug of the AC 

adapter into the DC input connector of 

the CU. 
Connect the AC adapter to a wall socket

 

 

 
 

Set the scanner on the CU. 
Take care not to involve a hand strap 
between the scanner and the CU. 

Push the scanner to the CU securely. 

 
 
 
 
 

 

The power indicator of the scanner turns 

red and charging starts. When the 

charging finishes, the power indicator 

turns green.   

 

When removing, pick up the scanner 

with the CU held with one hand. 

 
 
 
 

 

Power 

indicator 

 

    

AC adapter 

AD3-02 (FSP050-DBAE1) 

DC input connector 

Summary of Contents for SP1-QUBi














































Reviews: