background image

11

  ACCESSORIES

DESCRIPTION

PART NUMBER

Clear Vue

TM

 Muffle Door

9490738

  

Window Only

9390395

  

Door Only

9490737

Furnace Tongs

  10" Tongs

9390014

  12" Tongs

9390015

Furnace Trays

(see DENTSPLY Ceramco Catalog)

Furnace Calibration Kit

9982561

  PRODUCT SERVICE

Two methods of product service are available for the MINIGLAZE/2.  The first is telephone assistance available at the
numbers listed below.  The second is to return the furnace for servicing using the instructions below.

BEFORE RETURNING THE FURNACE, DO THE FOLLOWING:
•  Remove all firing trays and other loose items from inside the muffle.
•  The original packing material should be used for the return shipment.  Contact DENTSPLY Ceramco for

replacements if they are not available.

•  Call DENTSPLY Ceramco for a RMA number (Return Material Authorization).  This is used to track and identify

your furnace.  Material received without this number may not be identifiable.

•  Equipment damaged in shipment as the result of improper packing may not be paid by the carrier.  DENTSPLY

Ceramco will not be responsible for damages resulting from improper packing.

Ship Prepaid To:

TEL 909.795.2461

DENTSPLY Ceramco

FAX 909.795.5268

RMA Number __________
13553 Calimesa Blvd.
Yucaipa, CA 92399-2303 USA

Summary of Contents for Miniglaze/2













Reviews: