background image

TB-6502

  Page 8 of 8

 

                                                     

Revision May 2007

  

 

                                                      

© 2007 DESCO INDUSTRIES INC.                                          

Employee Owned

 

TECHNICAL SUPPORT:

 

 

USA

   

 

 

 

 

 

Europe 

Desco EMIT   

 

 

 

 

Charleswater 

3651 Walnut Avenue 

 

 

 

Unit 17, Millbrook Business Park, Sybron Way 

Chino, 

CA 

91710 

    Crowborough, East Sussex, TN6 3JZ, U.K. 

Tel:  (909) 627-8178 

   Tel: 

01892 

665313 

 

Fax: (909) 627-7449 

 

 

 

Fax: 01892 668838 

 

 
 

LIMITED WARRANTY

 

 
Desco EMIT expressly warrants that for a period of five (5) years from the date of purchase, Desco 
EMIT 50407 / 50413 will be free of defects in material (parts) and workmanship (labor). Within the 
warranty period, a credit for purchase of replacement Desco EMIT products, or, at Desco EMIT's 
option, the product will be repaired or replaced free of charge. If product credit is issued, the amount 
will be calculated by multiplying the unused portion of the expected five year life times the original unit 
purchase price. Call our Customer Service Department at 909-627-8178 (Chino, CA) or 781-821-8370 
(Canton, MA) for a Return Material Authorization (RMA) and proper shipping instructions and address. 
Please include a copy of your original packing slip, invoice, or other proof of date of purchase. Any 
unit under warranty should be shipped prepaid to the Desco EMIT factory. Warranty replacements will 
take approximately two weeks.

 

 
If your unit is out of warranty, 

Desco EMIT

 will quote repair charges necessary to bring your unit up 

to factory standards. Call Customer Service at 909-627-8178 for proper shipping instructions and 
address. Ship your unit freight prepaid. 
 

WARRANTY EXCLUSIONS

 

 
THE FOREGOING EXPRESS WARRANTY IS MADE IN LIEU OF ALL OTHER PRODUCT 
WARRANTIES, EXPRESSED AND IMPLIED, INCLUDING MERCHANTABILITY AND FITNESS FOR 
A PARTICULAR PURPOSE WHICH ARE SPECIFICALLY DISCLAIMED. The express warranty will 
not apply to defects or damage due to accidents, neglect, misuse, alterations, operator error, or failure 
to properly maintain, clean or repair products. 
 

LIMIT OF LIABILITY

 

 
In no event will 

Desco EMIT

 or any seller be responsible or liable for any injury, loss or damage, 

direct or consequential, arising out of the use of or the inability to use the product. Before using, users 
shall determine the suitability of the product for their intended use, and users assume all risk and 
liability whatsoever in connection therewith.

 

 

Summary of Contents for 50407









Reviews: