background image

 

 

TB-6534

  Page 8 of 8

 

                                                             

Revision 4/06

  

 

                                                      

© 2006 DESCO INDUSTRIES INC.                                       

Employee Owned

 

TECHNICAL SUPPORT: 

 

USA

   

 

 

 

 

 

Europe 

Desco 

EMIT 

     Charleswater 

3651 Walnut Avenue 

 

 

 

Unit 17, Millbrook Business Park, Sybron Way 

Chino, 

CA 

91710 

    Crowborough, East Sussex, TN6 3JZ, U.K. 

Tel:  (909) 627-8178 

   Tel: 

01892 

665313 

 

Fax: (909) 627-7449 

 

 

 

Fax: 01892 668838   

 
 

NOTE:

  Unauthorized servicing or modifications to your monitor will void the product warranty 

and may create dangerous conditions.  Servicing should be performed only at the factory, or 
by a Desco EMIT approved technician.   
 

 

LIMITED WARRANTY 

 

Desco EMIT expressly warrants that for a period of one (1) year from the date of purchase, Desco 
EMIT 

50665/50664 

will be free of defects in material (parts) and workmanship (labor). Within the 

warranty period, a unit will be tested, repaired, or replaced at our option, free of charge. Call Customer 
Service at 909-627-8178 (Chino, CA) or 01892 665313 (Crowborough, U.K.) for Return Material 
Authorization (RMA) and proper shipping instructions and address. Include a copy of your original 
packing slip, invoice, or other proof of date of purchase. Any unit under warranty should be shipped 
prepaid to the Desco EMIT factory.  Warranty replacements will take approximately two weeks. 
 
If your unit is out of warranty, Desco EMIT will quote repair charges necessary to bring your unit up to 
factory standards. Call Customer Service at 909-627-8178 for proper shipping instructions and address. 
Ship your unit freight prepaid.

 

 
WARRANTY EXCLUSIONS 
 

THE FOREGOING EXPRESS WARRANTY IS MADE IN LIEU OF ALL OTHER PRODUCT 
WARRANTIES, EXPRESSED AND IMPLIED, INCLUDING MERCHANTABILITY AND FITNESS FOR 
A PARTICULAR  PURPOSE WHICH ARE SPECIFICALLY DISCLAIMED. The express warranty will 
not apply to defects or damage due to accidents, neglect, misuse, alterations, operator error, or failure 
to properly maintain, clean or repair products.

 

 
LIMIT OF LIABILITY 
 

In no event will Desco EMIT or any seller be responsible or liable for any injury, loss or damage, direct 
or consequential, arising out of the use of or the inability to use the product. Before using, users shall 
determine the suitability of the product for their intended use, and users assume all risk and liability 
whatsoever in connection therewith.

 

Summary of Contents for 50664









Reviews: