background image

Total Exhaust Hood

Pg.9

18. Warranty

Design Filtration Inc. warrants the equipment to be free of defects in materials and
workmanship from the date of invoice.  The Total Exhaust Hood shall be warranted against
defects for a period of three years.  Any units or parts found to be defective during this
period will be replaced or repaired at our discretion.  The buyer agrees to assume all
transportation charges prepaid for return of unit to factory for repair.  Design Filtration Inc
will not accept charges for removal or re-installation. Design Filtration will not accept any
returned items without prior written consent.  Design Filtration Inc is not responsible for
repair or replacement by misuse or abuse by incorrect operating procedures of its
equipment.  Pre-filters carry no warranty against loading.  Any modifications or changes
made to equipment by customer without written consent of Design Filtration will void the
warranty. 

Model number and serial number located on the head section of your Total Exhaust Hood
must be provided to verify invoice date.  Failure to provide will void warranty. 

F

OR 

F

URTHER 

I

NFORMATION

,

 

P

LEASE 

C

ONTACT 

U

D

IRECTLY

.

Design Filtration Inc., 45 Iber Road, Ottawa, ON. K2S 1E7

T: 1-888-636-8609 (Canada & USA), T: 1-613-836-6065, F: 1-613-836-9724

info@designfiltration.com

Summary of Contents for TXH-4











Reviews: