background image

MP SERIES: INSTALLATION & OPERATION MANUAL

PAGE 3

IMPORTANT SAFETY INSTRUCTIONS

1.  Read these instructions.

2.  Keep these instructions.

3.  Heed all warnings.

4.  Follow all instructions.

5.  To prevent injury please refer to these instructions for electrical and safety information before installing

 

or operating the apparatus.

6.  No naked flame sources such as lighted candles should be placed on the apparatus.

7.  Operation of this apparatus is recommended for moderate climates only.

8.  This apparatus must not be exposed to dripping or splashing liquid.

 

No object filled with liquid, such as a vase, should be placed on the apparatus.

9.  Clean only with a dry cloth.

10.  Do not block any of the ventilation openings. Install in accordance with the manufacturer’s instructions.

11.  Do not install near any heat sources such as radiators, heaters, stoves, or other apparatuses

 

(including amplifiers) that produce heat.

12.  Unplug this apparatus during lightening storms or when not in use for long periods of time.

13.   

 Protective Earthing Terminal:

 

The apparatus should be connected to a mains socket outlet with a protective earthing connection.

14.  The mains plug/appliance coupler is used as a disconnect device, the disconnect device shall remain 

readily operable.

15.  When not in use and during transportation, please take care of the power cord set, for example, tie up 

the power cord set with a cable tie/something similar. It should be kept away from sharp edges and 
the like that can cause abrasion of the power cord set. When put into use again, check that the power 
cord set is not damaged. If any damage is found, have the unit checked by a qualified service person 
to replace the power cord set specified by the manufacturer.

16.  The terminals marked with symbol of “ 

   “ may be of sufficient magnitude to constitute a risk of 

electric shock. The external wiring connected to the terminals requires installation by a qualified service 
person or the use of ready-made leads or cords.

17.  Only use attachments/accessories specified by the manufacturer.

18.  Check speaker line load prior to connecting to amplifier using an impedance meter.

19.  Refer all servicing to qualified service personnel. Servicing is required if the apparatus has been 

damaged in any way, such as power-supply cord or plug breakage, damage due to liquid or objects 
falling onto the apparatus, exposure to rain or moisture, or if the apparatus does not operate normally, 
or has been dropped.

20.   

  Correct Disposal of this Product:

 

This marking indicates that this product should not be disposed of with other household wastes. To 
prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle 
it responsibly to promote the sustainable reuse of material resources. To return your used device, please 
use the return and collection systems or contact the retailer where the product was purchased. They 
can take this product for environmental-safe recycling.

WARNING: There are no user serviceable parts inside. Refer all servicing to qualified service personnel.

Summary of Contents for MP 30











Reviews: